POPPUR爱换

 找回密码
 注册

QQ登录

只需一步,快速开始

手机号码,快捷登录

搜索
查看: 7296|回复: 5

perc 6/i刷死了 ...

[复制链接]
发表于 2014-7-30 19:08 | 显示全部楼层 |阅读模式
一开始是不认SATA盘,用MegaCli -AdpAllInfo -aALL 查raid卡信息:
Adapter #0

==============================================================================
                    Versions
                ================
Product Name    : PERC 6/i Integrated
Serial No       : 1122334455667788
FW Package Build: 6.3.0-0001

                    Mfg. Data
                ================
Mfg. Date       : 06/24/08
Rework Date     : 06/24/08
Revision No     :
Battery FRU     : N/A

                Image Versions in Flash:
                ================
FW Version         : 1.22.12-0952
BIOS Version       : 2.04.00
WebBIOS Version    : 1.1-46-e_15-Rel
Ctrl-R Version     : 1.02-015B
Preboot CLI Version: 01.00-023:#%00006
Boot Block Version : 1.00.00.01-0011

                Pending Images in Flash
                ================
None

                PCI Info
                ================
Controller Id        : 0000
Vendor Id       : 1000
Device Id       : 0060
SubVendorId     : 1028
SubDeviceId     : 1f0c

Host Interface  : PCIE

Link Speed              : 0
Number of Frontend Port: 0
Device Interface  : PCIE

Number of Backend Port: 8
Port  :  Address
0        0000000000000000
1        0000000000000000
2        0000000000000000
3        0000000000000000
4        0000000000000000
5        0000000000000000
6        0000000000000000
7        0000000000000000

                HW Configuration
                ================
SAS Address      : 50022190a4efab00
BBU              : Present
Alarm            : Absent
NVRAM            : Present
Serial Debugger  : Present
Memory           : Present
Flash            : Present
Memory Size      : 256MB
TPM              : Absent
On board Expander: Absent
Upgrade Key      : Absent
Temperature sensor for ROC    : Absent
Temperature sensor for controller    : Absent


                Settings
                ================
Current Time                     : 17:5:37 7/30, 2014
Predictive Fail Poll Interval    : 300sec
Interrupt Throttle Active Count  : 16
Interrupt Throttle Completion    : 50us
Rebuild Rate                     : 30%
PR Rate                          : 30%
BGI Rate                         : 30%
Check Consistency Rate           : 30%
Reconstruction Rate              : 30%
Cache Flush Interval             : 4s
Max Drives to Spinup at One Time : 2
Delay Among Spinup Groups        : 12s
Physical Drive Coercion Mode     : 128MB
Cluster Mode                     : Disabled
Alarm                            : Disabled
Auto Rebuild                     : Enabled
Battery Warning                  : Enabled
Ecc Bucket Size                  : 15
Ecc Bucket Leak Rate             : 1440 Minutes
Restore HotSpare on Insertion    : Disabled
Expose Enclosure Devices         : Disabled
Maintain PD Fail History         : Disabled
Host Request Reordering          : Enabled
Auto Detect BackPlane Enabled    : SGPIO/i2c SEP
Load Balance Mode                : Auto
Use FDE Only                     : No
Security Key Assigned            : No
Security Key Failed              : No
Security Key Not Backedup        : No
Default LD PowerSave Policy      : Controller Defined
Maximum number of direct attached drives to spin up in 1 min : 0
Auto Enhanced Import             : No
Any Offline VD Cache Preserved   : No
Allow Boot with Preserved Cache  : No
Disable Online Controller Reset  : No
PFK in NVRAM                     : No
Use disk activity for locate     : No
POST delay                         : 90 seconds
BIOS Error Handling                   : Stop On Errors
Current Boot Mode                   :Normal
                Capabilities
                ================
RAID Level Supported             : RAID0, RAID1, RAID5, RAID6, RAID00, RAID10, RAID50, RAID60, PRL 11, PRL 11 with spanning, SRL 3 supported, PRL11-RLQ0 DDF layout with no span, PRL11-RLQ0 DDF layout with span
Supported Drives                 : SAS, SATA

Allowed Mixing:

Mix in Enclosure Allowed

                Status
                ================
ECC Bucket Count                 : 0

                Limitations
                ================
Max Arms Per VD          : 32
Max Spans Per VD         : 8
Max Arrays               : 128
Max Number of VDs        : 64
Max Parallel Commands    : 1008
Max SGE Count            : 80
Max Data Transfer Size   : 8192 sectors
Max Strips PerIO         : 42
Max LD per array         : 16
Min Strip Size           : 8 KB
Max Strip Size           : 1.0 MB
Max Configurable CacheCade Size: 0 GB
Current Size of CacheCade      : 0 GB
Current Size of FW Cache       : 0 MB

                Device Present
                ================
Virtual Drives    : 0
  Degraded        : 0
  Offline         : 0
Physical Devices  : 0
  Disks           : 0
  Critical Disks  : 0
  Failed Disks    : 0

                Supported Adapter Operations
                ================
Rebuild Rate                    : Yes
CC Rate                         : Yes
BGI Rate                        : Yes
Reconstruct Rate                : Yes
Patrol Read Rate                : Yes
Alarm Control                   : Yes
Cluster Support                 : No
BBU                             : Yes
Spanning                        : Yes
Dedicated Hot Spare             : Yes
Revertible Hot Spares           : Yes
Foreign Config Import           : Yes
Self Diagnostic                 : Yes
Allow Mixed Redundancy on Array : No
Global Hot Spares               : Yes
Deny SCSI Passthrough           : No
Deny SMP Passthrough            : No
Deny STP Passthrough            : No
Support Security                : No
Snapshot Enabled                : No
Support the OCE without adding drives : No
Support PFK                     : No
Support PI                      : No
Support Boot Time PFK Change    : No
Disable Online PFK Change       : No
Support Shield State            : No
Block SSD Write Disk Cache Change: No

                Supported VD Operations
                ================
Read Policy          : Yes
Write Policy         : Yes
IO Policy            : Yes
Access Policy        : Yes
Disk Cache Policy    : Yes
Reconstruction       : Yes
Deny Locate          : No
Deny CC              : No
Allow Ctrl Encryption: No
Enable LDBBM         : No
Support Breakmirror  : No
Power Savings        : No

                Supported PD Operations
                ================
Force Online                            : Yes
Force Offline                           : Yes
Force Rebuild                           : Yes
Deny Force Failed                       : No
Deny Force Good/Bad                     : No
Deny Missing Replace                    : No
Deny Clear                              : No
Deny Locate                             : No
Support Temperature                     : No
NCQ                                     : No
Disable Copyback                        : No
Enable JBOD                             : No
Enable Copyback on SMART                : No
Enable Copyback to SSD on SMART Error   : No
Enable SSD Patrol Read                  : No
PR Correct Unconfigured Areas           : Yes
                Error Counters
                ================
Memory Correctable Errors   : 0
Memory Uncorrectable Errors : 0

                Cluster Information
                ================
Cluster Permitted     : No
Cluster Active        : No

                Default Settings
                ================
Phy Polarity                     : 0
Phy PolaritySplit                : 0
Background Rate                  : 30
Strip Size                       : 64kB
Flush Time                       : 4 seconds
Write Policy                     : WB
Read Policy                      : None
Cache When BBU Bad               : Disabled
Cached IO                        : No
SMART Mode                       : Mode 6
Alarm Disable                    : No
Coercion Mode                    : 128MB
ZCR Config                       : Unknown
Dirty LED Shows Drive Activity   : No
BIOS Continue on Error           : 0
Spin Down Mode                   : None
Allowed Device Type              : SAS/SATA Mix
Allow Mix in Enclosure           : Yes
Allow HDD SAS/SATA Mix in VD     : No
Allow SSD SAS/SATA Mix in VD     : No
Allow HDD/SSD Mix in VD          : No
Allow SATA in Cluster            : No
Max Chained Enclosures           : 1
Disable Ctrl-R                   : No
Enable Web BIOS                  : No
Direct PD Mapping                : Yes
BIOS Enumerate VDs               : Yes
Restore Hot Spare on Insertion   : No
Expose Enclosure Devices         : No
Maintain PD Fail History         : No
Disable Puncturing               : No
Zero Based Enclosure Enumeration : Yes
PreBoot CLI Enabled              : No
LED Show Drive Activity          : No
Cluster Disable                  : Yes
SAS Disable                      : No
Auto Detect BackPlane Enable     : SGPIO/i2c SEP
Use FDE Only                     : No
Enable Led Header                : No
Delay during POST                : 0
EnableCrashDump                  : No
Disable Online Controller Reset  : No
EnableLDBBM                      : No
Un-Certified Hard Disk Drives    : Block
Treat Single span R1E as R10     : No
Max LD per array                 : 16
Power Saving option              : All power saving options are enabled
Default spin down time in minutes: 0
Enable JBOD                      : No
Time taken to detect CME         : 60s

Exit Code: 0x00

发现:
Allow HDD SAS/SATA Mix in VD     : No
Un-Certified Hard Disk Drives    : Block
google一大圈没找到更改设置的命令,就想刷下最新6.3.3-0002试试,结果运行早就编辑好的刷固件批处理的时候,选了刷H310的megrec的cleanflash的那个批处理,cleanflash后看到提示重启了,运行m0flash就一直卡在

megaraid hwr contoller recovery  tool,version 01.01-004 rebruary 05,2010
copyright 2006-2008 lsi corp.
supports 1078 controller and its successors.
setting up he chip for host-boot......
please do power cycle the host machine
please do not warm reboot by pressing (ctrl+alt+del)key
please make sure you removed the default jumper before you power on the system
-光标一直在这闪啊闪,
等了十几分钟看没反应,就出去吃饭,回来才发现,小区施工停电了,再开机试试这命令也一直卡在这了;

megarec -adplist查看:
...
megaraid hwr contoller recovery  tool,version 01.01-004 rebruary 05,2010
copyright 2006-2008 lsi corp.
supports 1078 controller and its successors.
identified MR cards count:1
list of identified cards
----------------------------
MR Card 0
type:1078
vendor ID:0x1000,device ID:0x60
slot NO:2,device function:0x0
press a key to continue....

但是用MegaCli -AdpAllInfo -aALL已经认不到卡了:
......
copytight (c)supernar systems,LTD,1995-2002
dos/32a warning(9004):mouse initialization failed

F/W is in Fault state
Exit code:0x00

球大神指导,这卡还有救么?
发表于 2014-7-31 09:28 | 显示全部楼层
扔了,TB 100米再买个!
回复 支持 反对

使用道具 举报

发表于 2014-8-4 17:26 | 显示全部楼层
1078芯片使用megarec的时候要单独刷一个启动的引导
回复 支持 反对

使用道具 举报

 楼主| 发表于 2014-8-5 12:29 | 显示全部楼层
本帖最后由 wxlg1117 于 2014-8-5 12:57 编辑
coldcoffee 发表于 2014-8-4 17:26
1078芯片使用megarec的时候要单独刷一个启动的引导


,怎么个操作法?serial boot rom么?
回复 支持 反对

使用道具 举报

发表于 2014-8-5 15:03 | 显示全部楼层
操作步骤
1,把我上传的文件解压出来,有两个文件,bb4k.rom和6ii.sbr(如果你之前有保存sbr就用你自己的)
2,把bb4k.rom  megarec.exe ,dos4gw.exe 还有你的fw文件(比如 fw437ii.rom) 放在同一个文件夹里
3,DOS启动进去你的文件夹,运行 megarec -cleanflash 0 fw437ii.rom ,这样就还是提示之前的,但是注意上面已经提示了不能热启动,要关电源,然后再开机
4,重新开机,进去原来的文件夹,里面多了两个文件,autoexec.bat 和rec.bat ,运行 autoexec.bat(其实运行rec.bat也是一样的,只不过你要是放在dos根目录下就会自动运行,autoexec.bat只是运行rec.bat)
5,运行 megarec -writesbr 0 6ii.sbr
6,重启,祝你成功

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有帐号?注册

x
回复 支持 反对

使用道具 举报

发表于 2014-8-10 18:30 | 显示全部楼层
学习学习
回复 支持 反对

使用道具 举报

您需要登录后才可以回帖 登录 | 注册

本版积分规则

广告投放或合作|网站地图|处罚通告|

GMT+8, 2024-3-29 03:37

Powered by Discuz! X3.4

© 2001-2017 POPPUR.

快速回复 返回顶部 返回列表