|
|
除Adaptec 5805外，其他型號也推出了新版Firmware
==============================================
Adaptec RAID Release dated: December 04, 2008
==============================================
This release notes contain the following:
1. Description of the Release
2. Supported Controllers
3. Enhancements and Bugfixes
1. Description of the Release:
===============================
This is the official software release containing the list of software components listed below:
- Firmware Version 5.2.0 Build 16343
- Windows Driver (32-bit and 64-bit) Version 5.2.0.16343
- SCO UnixWare and OpenServer Driver Version 5.2.0.16343
- FreeBSD Driver Version 5.2.0.16343
- Solaris Driver Version 5.2.0.16343
- Linux Driver Version 1.1.5-2459
- Adaptec Storage Manager (ASM) Version 6.10 Build 18350
2. Supported Controllers:
=========================
- Adaptec RAID 5405
- Adaptec RAID 5445
- Adaptec RAID 5805
- Adaptec RAID 5085
- Adaptec RAID 51245
- Adaptec RAID 51645
- Adaptec RAID 52445
- Adaptec RAID 2405
- Adaptec RAID 2045
3. Enhancements and Bug Fixes:
==============================
- Added support for FreeBSD 7.0
- Incorporated SLI Maintenance Release 2
- Improved handling of Direct Access Storage Devices (i.e. Removable Drives)
- Increased the number of drives to be used in a RAID6 to 32
- Improved linear read/write performance scaling for RAID5 and RAID6 configurations
- Improved initialization time for certain large configurations
- Improved Power Management support in ARCCONF and Adaptec Storage Manager
- Improved the Ctrl+A options for application aware performance tuning
- Added display of Device ID to ARCCONF "get log" command
- Added option to the Ctrl+A utility to manage Global Hot Spares independently
- Added option to the Ctrl+A utility to change cache settings for logical drives after their creation
- Added option for Secured Email Notification in Adaptec Storage Manager
- Fixed a discovery issue with backplanes using LSI Expanders
- Fixed an issue where the speed of SATA II devices intermittently changed to 1.5GB on PowerON/OFF or remove
- Fixed an issue where the speed of SATA I devices didn't show up correctly when connected behind an expander
- Fixed an issue where Adaptec Storage Manager closed under OpenServer 6.0 after the controller logs were cleared
- Fixed a mismatch in device names between Adaptec Storage Manager and ARCCONF
- Fixed an issue where SNMP showed incorrect Host Bus Information
- Fixed an issue where alarm actions and changes in task priorities in ARCCONF didn't generate an event
- Fixed an issue where Adaptec Storage Manager didn't allow the expansion of a RAID5EE
- Fixed an issue where Adaptec Storage Manager was not able to successfully finish a migration from RAID0 to RAID10 in SLES10
- Fixed an issue where a fully populated AIC XC-28-2 Enclosure caused the Controller kernel to panic
- Fixed an issue where the alarm didn't go silent on a rebuilding array
- Fixed an issue where a stopped build process didn't show the status of the RAID array correctly in FreeBSD
- Fixed an issue where the initialization of a drive didn't remove the Global Hot Spare designation
- Fixed an issue where tape drives showed an incorrect "standby" status
- Fixed an issue on Series-2 controllers where the Copyback Hot Spare option was missing
- Fixed an issue where the installation of the 64-bit Windows SCSIport driver asked for a missing DLL
- Fixed an issue where the Windows Backup Utility reported a bus reset because of an device error
- Fixed an issue with Fault LED support on the Xtore MiniBOD XJ-SA01-008-A1
====================================================================
Firmware Download:
http://download.adaptec.com/raid/asr/fw_bios/5805_fw_b16343.exe |
|
IP卡
狗仔卡
发表于 2008-12-10 18:53
QQ好友和群
收藏
分享
好贴
烂贴
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
显身卡