POPPUR爱换

标题: [更新]LSI LSISAS2108 6Gb/s新版韌體發佈(嚴重注意事項!) [打印本页]

作者: per1-q1222 时间: 2011-10-15 04:12
标题: [更新]LSI LSISAS2108 6Gb/s新版韌體發佈(嚴重注意事項!)
本帖最后由 per1-q1222 于 2011-10-15 04:23 编辑

此版韌體不能和CacheCade Pro 2.0轉換使用....
此舉很有可能破壞原有的VD結構, 並且使VD無法讀取....
如果您不小心刷到這個f/w導致VD無法讀取該何解??
由於這個情況有可能是因為NVDATA的差異性導致一種native configuration is not supported的錯誤原因...
這時您只要刷回先前的韌體, 讓MegaRAID做一次OAR, VD應該就會回復了...
此版韌體已經完全把Power Saving on Configured Drives徹底關閉了..

顯示出LSI漠視舊客戶的權益.......

這個f/w基於10M09變更的, 所以完全不支援CacheCade Pro 2.0
此版f/w新增了一種緊急Hotspare機能, 這跟sheild state有關係..
但這項功能是完全關閉的, 不排除LSI做成高階軟件的可能性....

LSI在這樣欺負消費者...
我就要轉到Adaptec by PMC了...

目前能做的就是在Mail嚴重抗議這種行為...

此版固件不是先前CacheCade Pro 2.0的升級固件...
download:
http://www.lsi.com/downloads/Public/MegaRAID%20Common%20Files/12.12.0-0073_SAS_2108_FW_Image_APP-2.120.183-1415.zip

Component:
=========
SAS MegaRAID Firmware Release for MegaRAID Controllers
Release date: 10/14/11

Version Numbers:
===============
Current Firmware Package: 12.12.0-0073
Current Package Details:
APP-2.120.183-1415_BB-2.02.00.00-0000_BIOS-3.23.00_4.11.05.00_0x05080000_HII-_WEBBIOS-6.0-45-e_40-Rel_PCLI-04.04-017_SPRINT400008_BOOT-09.250.01.219_NVDATA-2.09.03-0024_2011_10_05

Previous Firmware Package: 12.12.0-0048
Previous Package Details:
APP-2.120.63-1242_BB-2.02.00.00-0000_BIOS-3.22.00_4.11.05.00_0x05020000_HII-_WEBBIOS-6.0-34-e_29-Rel_PCLI-04.04-01700008_BOOT-09.250.01.219_NVDATA-2.09.03-0013_2011_04_06


Bug Fixes and Enhancements:
===========================
Firmware:
=========
LSIP200149248 (CO) Warning for High Error Counts
LSIP200149890 (CO) SW licensing. Support FoD for PF activations on iMR/2008
LSIP200187910 (CO) Request to use Unconfigured Good Drives for a HotSpare if no spare defined in liberator
LSIP200187724 (CO) MR fw should Enable puncturing for SATA drives
LSIP200187937 (CO) MegaRaid does not pick up replacement drives in PD if replacement is added during power cycle
LSIP200151375 (CO) Need StopOnError functionality when SafeStore passphrase is enabled
LSIP200187926 (CO) Change BBU-08 support Firmware Mode5 WB capacity from 960mAh to 674mAh
LSIP200187931 (CO) disable bad phy checking logic from iMR FW for certain ROMB design
LSIP200199858 (CO) add display of ibbu communication retry counter in 10M09 fw log
LSIP200199484 (CO) Enable copy back on SMART - Liberator
LSIP200186977 (CO) Alert should be sent when one phy connector between Liberator card and SAS expander is degraded
LSIP200149050 (CO) Add SGPIO for Medusa
LSIP200186343 (CO) (LSIP200140211) Add support to pass SMART errors for JBOD drives to MSM
LSIP200185599 (DFCT) LED behavior incorrect, drive 3 blinks when drive 0 is accessed
LSIP200209385 (DFCT) Intermittent RAID key failure during power-on
LSIP200209329 (DFCT) FoD features will not activate or deactivate
LSIP200156822 (DFCT) CC2.0: WT Downgrade FW from CC2.0 to CC1.0(10M09) and import caused MonTask: line 199 in file ../../raid/1078int.c
LSIP200149201 (DFCT) (CL LSIP200146291) Medium error handling fixes for >2TB
LSIP200199812 (DFCT) Alarm sounds with online VD's after flashing latest 10M09 Patch 16 firmware (2.120.163-1343)
LSIP200199961 (DFCT) (CL LSIP200061413) LDBBM entries are incorrect after foreign import
LSIP200186336 (DFCT) Controller does not work with pci set to nomsi in kdump kernel
LSIP200209455 (DFCT) (CL LSIP200188135) Potential data integrity issue running the IO on degraded R5 VDs with 32 drives.
LSIP200158264 (DFCT) Change the capacity level that generates the Predictive failure alert
LSIP200150304 (DFCT) memory test for 2108 in 10M09 FW fails immediately
LSIP200149986 (DFCT) MSM log shows "Battery cannot initiate transparent learn cycles" due to BBU is under mode 5.
LSIP200060949 (DFCT) iBBU07 reported remaining capacity is much too high (64751 mAh) after a learn cycle
LSIP200151502 (DFCT) BBU Absolute Charge is displayed differently
LSIP200149843 (DFCT) VPD (Vital Product Data) needs to show correct Part number
LSIP200149844 (DFCT) VPD (Vital Product Data) needs to identify PCB hardware level
LSIP200199416 (DFCT) Change BBU-08 support Firmware Mode5 WB capacity from 960mAh to 674mAh for low power DDR-2
LSIP200199331 (DFCT) 10M09: Older ibbu batteries display 65K capacity and are marked SOH bad
LSIP200199335 (DFCT) 10M09: Request FW to not mark ibbu battery as bad when very high capacity is detected
LSIP200196885 (DFCT) Batteries Not Charging
LSIP200209376 (DFCT) HWR: 10M09: OEM requests ibbu i2c communication retries to be displayed in fw log
LSIP200147629 (DFCT) (CL LSIP200167360) FW hit montask upon importing foreign config
LSIP200147626 (DFCT) (CL LSIP200139418) System reboots after issuing OCR
LSIP200147907 (DFCT) Disable Dimmer Switch III
LSIP200151221 (DFCT) CLI/EFI CLI/PCLI fail to create a VD on MR
LSIP200148150 (DFCT) WHQL WLK1.6 - SCSI Compliance Test 2.0 and Read Capacity 16 Unit FAILS on Liberator
LSIP200184970 (DFCT) HWR: 10M09: not able to disable BGI with MegaCLI
LSIP200173287 (DFCT) HWR: bbuMode is not in WebBIOS after flashing from 10M05 to 10M09
LSIP200186884 (DFCT) HWR: 10M09: DelaySOD is not working on customer Liberator boards
LSIP200150532 (DFCT) (RW LSIP200145892) (6997086) (RW LSIP200121969) Liberator FW 10M09 cause system (sles11sp1/rhel6) reset while lspci -vvx
LSIP200188226 (DFCT) HWR 10M09 can't sustain at least 950 MBps performance with Cache Flush setting 1 sec
LSIP200200459 (DFCT) MegaCli prematurely returns exit 0x0 status on drive firmware flash
LSIP200209349 (DFCT) Enable PCI capability Bit for VPD exsupport.
LSIP200151328 (DFCT) HWR: EF & 10M09: bluescreen occurs handling R1 with HSP and medium errors
LSIP200186966 (DFCT) HWR: 10M09: configuration becomes foreign after fw fails 3-4 attempts to access raid key during boot
LSIP200147621 (DFCT) (CL LSIP200163913) performance issues within 9285 and 9280 caused by the MegaRAID FW
LSIP200147632 (DFCT) (CL LSIP200173232) Potential data integrity issue found on R1 VDs while injecting the media errors under IO.
LSIP200186406 (DFCT) Code Review defect to deliver rest of changes for PFK preboot support.
LSIP200186594 (DFCT) R5 pfk feature not getting enabled at boot time on iMR
LSIP200186595 (DFCT) After loading FoD key, iMR controller does not perform upgrade of features
LSIP200188345 (DFCT) (CL LSIP200185468) HWR: 10M09: extended retries of write verify command causes driver timeout
LSIP200171125 (DFCT) No event is generated when fan in enclosure fails
LSIP200184943 (DFCT) Need ability to boot with pinned cache with any raid config on Gen 2 MegaRAID/Liberator defaulted to ON
LSIP200185931 (DFCT) Bootwithpinnedcache not default set to '1' for castorlite when suboem is '1'
LSIP200186584 (DFCT) Logical Unit ID (VPD page 0x83) changed after foreign import
LSIP200198521 (DFCT) 10M09 P16 set properties command fails
LSIP200146463 (DFCT) Update OOB (BMC) management
LSIP200171812 (DFCT) Liberator Firmware : Fatal F/W Error* happened when detected drive error** during Read I/O.
LSIP200169751 (DFCT) MegaRaid FW does not wait at post

Webbios:
========
LSIP200199949 (CO) SW licensing. Support FoD for PF activations on MegaRAID
LSIP200188273 (DFCT) uEFI WebBIOS incorrectly displays "UG Spin Down" title
LSIP200139977 (DFCT) Option for populating the VD size field automatically
LSIP200156291 (DFCT) can't create DG with 8 PDs with enableReducedFeatureSet
LSIP200157087 (DFCT) EFI WebBIOS does not show product name/version for second adapter in adapter selection screen
LSIP200121693 (DFCT) Unable to configure Cachecade in webBIOS under 10M09 for 2108 based products
LSIP200166733 (DFCT) WEBBIOS is unable to reconstruct the R11 VD to R5 with removal of one PD.
LSIP200147461 (DFCT) Cannot change the BBU properties in webbios
LSIP200149524 (DFCT) WebBIOS gives garbled message when enabing FDE on an existing Disk Group

BIOS:
========
LSIP200196810  SWR-Macon: After installing the OS, unable to boot from SCU VD
LSIP200199602  FW hangs during POST after flashing new BIOS
LSIP200018807  BIOS sees extra characters "0%" at end of particular product name
LSIP200156493  There is no space between FW version and capacity in the table where Adp/VD/PD info is displayed
Numerous HII fixes

作者: dracocephalum 时间: 2011-10-15 09:14
我有感覺 DELL 遲遲不出 PERC H700 FW 更新也是因爲 LSI 跟 DELL 談不攏……
DELL 不想花錢，LSI 說新 FW 裏面全部是高級功能必須給錢……
有點欺負人的感覺……

作者: nqhjl 时间: 2011-10-15 10:30
提示: 作者被禁止或删除内容自动屏蔽

作者: stephenmaxmax 时间: 2011-10-15 14:57
本帖最后由 stephenmaxmax 于 2011-10-15 15:07 编辑

请教下楼主，9260-8i有时候会用着用着上面的阵列直接消失，msm中刷新后直接没有发现那张卡
重启服务器有时候卡和阵列会回来，有时候还是检测不到，用IPMI远程过去可以看到系统自检时，只有板载的sas2008自检到了，9260并没进行自检过程。

系统是2008r2
卡消失时会有系统日志：
megasas2 发出了对设备 \Device\RaidPort1 的重置。
megasas2 驱动程序在 \Device\RaidPort1 上检测到控制器错误。

阵列应该没问题，也没坏盘，大概是卡要挂了吧，可是是今年才买的。不过好在不是行货，也没多贵。。

附件是tty log，可以看到刷了fw，但这问题是刷fw之前就出现的，刷fw把之前的log清了，所以看不到之前的。
然后日志里有条背板风扇的Critical，这个不要紧，是因为我把背板风扇接主板上去了

PS：这卡没保。

作者: hunun 时间: 2011-10-15 19:08
黑心的lsi

作者: per1-q1222 时间: 2011-10-16 07:46
本帖最后由 per1-q1222 于 2011-10-16 07:46 编辑

stephenmaxmax 发表于 2011-10-15 14:57
请教下楼主，9260-8i有时候会用着用着上面的阵列直接消失，msm中刷新后直接没有发现那张卡
重启服务器有时 ...

你的TTY Log我目前沒看到有關RAID控制器(主控)相關錯誤訊息..
我倒是看到其他錯誤訊息:
1. fail fan error
2. 有關PD的錯誤訊息

我上個月有看到你這種類似的案例..
不過對方是H700...

作者: stephenmaxmax 时间: 2011-10-16 12:56
本帖最后由 stephenmaxmax 于 2011-10-16 13:04 编辑

per1-q1222 发表于 2011-10-16 07:46
你的TTY Log我目前沒看到有關RAID控制器(主控)相關錯誤訊息..
我倒是看到其他錯誤訊息:
1. fail fan er ...

有时候会有Controller Hot Plug detected的日志
风扇的问题是正常的，因为背板风扇没有插在背板上，而是插在主板上了。（插背板上转速太高声音太吵。。）
PD那些错误倒是一直都有，很莫名。。

T0: LSI ROC firmware
T0: Copyright(C) LSI Corporation, 2010
T0: Firmware version 2.130.03-1332 built on Aug 5 2011 at 11:54:07

T0: DRAM Sig from the Prev boot
T0: *** HW Encryption Disabled : dcrReg=80000001
T0: setAdapterResetTime: CCR_MISC_CFG 8002ff2c
T0: DRAM_LOCAL_BASE: 80000000
T0: MEM_FIXED_SIZE: 5a00000
T0: FW_DRAM_REGION_START: 85a00000
T0: FW_DRAM_REGION_SIZE: 2200000
T0: MEM_POOL_BASE: 86d941d0
T0: Initializing memory pool size=00E6BE30 bytes
T0: Press '!' within 3 seconds to enter debugger before INIT

有时候这之后卡就不再继续自检了

还有，请问，我能买一块9240-4i或是IBM fw的M5015替代吗，阵列会消失吗？还是必须买个一模一样的，阵列才不会消失？

作者: per1-q1222 时间: 2011-10-16 13:30
本帖最后由 per1-q1222 于 2011-10-16 13:32 编辑

stephenmaxmax 发表于 2011-10-16 12:56
有时候会有Controller Hot Plug detected的日志
风扇的问题是正常的，因为背板风扇没有插在背板上，而是 ...

你可以用M5015, 但是不可以用9240系列和M1015...
只要port slot沒有變化...
裝上新的HBA, HBA開機初始化時便會進行OAR(Online RAID Roaming)操作...
會將VD上的metadate進行重載, 然後設定到HBA上的NVRAM..
正常情況下, 所有VD資訊便會自動回復...

你也許可以關機一段時間看看..
等RAID主控冷卻以後重新開機一段時間...
看看會不會再次出現情況...
可能是不是過熱問題, 由於LSISAS2108產品並沒有提供Controller和Chip溫度監控支持..
所以比較麻煩..

作者: stephenmaxmax 时间: 2011-10-16 14:20
本帖最后由 stephenmaxmax 于 2011-10-16 14:27 编辑

哦，刚才打错了，是9260-4i
不是温度问题，因为专门有片pci位风扇对着吹的，一般只是稍温而已
其实我怀疑那张卡哪个阵脚虚焊了，或许是运输问题导致。

m5015很便宜，，，我打算买个换上。启动慢和不支持raid6对我来说倒是没关系。。
其实我有点受够了硬件raid了，打算换成mdraid或zfs（主板上有个sas2008），不过没有卡也无法从原来的阵列导出数据，但买了卡大概又懒得去换成软raid了。。

作者: idolclub 时间: 2011-10-18 00:12
自去年推出CacheCade等Software License後已感覺到LSI要徹底的奉行利潤最大化了

作者: idolclub 时间: 2011-10-19 11:57
LSI突然在網站上移除了此版Firmware

作者: 声色茶马 时间: 2011-10-19 12:06

idolclub 发表于 2011-10-19 11:57
LSI突然在網站上移除了此版Firmware

支持楼主，关注进展。

作者: per1-q1222 时间: 2011-10-21 05:43
LSI FTP反而擺上了該固件..

作者: jimmyjin 时间: 2011-10-21 13:13
移除Dimmer Switch？那无视吧....... 继续用老的9260-8i固件。
对没有SSD Cache的我来说， H700对6i 最大的差别就是dimmer swicth

作者: per1-q1222 时间: 2011-10-25 12:20
LSI又把這個f/w擺到網站上了..

作者: per1-q1222 时间: 2011-10-25 12:23

jimmyjin 发表于 2011-10-21 13:13
移除Dimmer Switch？那无视吧....... 继续用老的9260-8i固件。
对没有SSD Cache的我来说， H700对6i 最大 ...

無良的LSI..
昨天mail問他們:
per1-q1222:
why did you disable dimmer switch III on the latest f/w??

LSI FAE:
I am not entirely sure why it was decided to be removed from the latest firmware. It can still be set in MegaRAID Storage Manager or using MegaCLI as you can see in the article below.
http://kb.lsi.com/KnowledgebaseA ... words=Dimmer+Switch
http://kb.lsi.com/KnowledgebaseArticle16385.aspx

他講的那兩個連結根本沒用..
都被關掉了..
我要怎麼設定??

作者: dracocephalum 时间: 2011-10-25 15:34

per1-q1222 发表于 2011-10-25 16:23
無良的LSI..
昨天mail問他們:
per1-q1222:

我有預感，Dimmer Switch III 要改名字了……
所以功能就沒了~~

那個 LSI 工作人員在裝傻，把 Dimmer Switch III 硬是看作整個 Dimmer Switch 功能系列了...

作者: jimmyjin 时间: 2011-10-25 17:35

per1-q1222 发表于 2011-10-25 12:23
無良的LSI..
昨天mail問他們:
per1-q1222:

DimmerSiwther II 就可以spindown configured disk 了对吧？
有没可能LSI 只是关了针对SAS的部分， SATA HDD 还是可以的？这是我对LSI满怀善意的想法.
不过我还是不想去试这个F/W了

作者: per1-q1222 时间: 2011-10-25 17:52
本帖最后由 per1-q1222 于 2011-10-25 17:53 编辑

jimmyjin 发表于 2011-10-25 17:35
DimmerSiwther II 就可以spindown configured disk 了对吧？
有没可能LSI 只是关了针对SAS的部分， SATA ...

只有Dimmer Switch III才支持spin-down on configured disks..
也就是不支持這個功能...
不管SATA或著SAS..
轉入Virtual Disk..
一律都不能spin-down..

作者: stephenmaxmax 时间: 2011-10-25 17:57
其实我现在觉得不spin down对硬盘反而有好处
硬盘有很长的MTBF但是可以承受的起转次数相对有限。

作者: dracocephalum 时间: 2011-10-26 10:59
其實spin down configure應該對3.5吋的硬盤有點用處。2.5吋的本身功耗就比較低，SSD就更不用說。
現在我是 Adaptec 5805 帶全部 3.5吋硬盤（Adaptec有spin down configured），然後 H700 帶 2.5+SSD，有沒有spin down無所謂了……

作者: stephenmaxmax 时间: 2011-10-26 11:11
其实这点功耗有什么。。
我可是功耗计买了就没拔下来过，盘阵(24盘插进了16盘)耗电量真心的不高，都没打游戏时显卡耗电多。

欢迎光临 POPPUR爱换 (https://we.poppur.com/)