POPPUR爱换

标题: LSISAS2208/2108/2008 New IMR f/ws, drivers and tools from IBM [打印本页]

作者: per1-q1222 时间: 2012-6-13 05:29
标题: LSISAS2208/2108/2008 New IMR f/ws, drivers and tools from IBM
本帖最后由 per1-q1222 于 2012-6-13 05:35 编辑

LSI MegaRAID SAS Driver, v5.2.127, windows 2k8, x86/x64
lsi_raid_megaraid_driver_v5_2_127_win2k8_x86_x64.7z
LSI MegaCLI, v8.04.07,x86/x64
lsi_raid_megaraid_megacli_v8_04_07_x86_x64.7z

LSISAS2208, v23.7.0-0029, CC Pro 2.1 supported
lsi_raid_megaraid_fw_lsisas2208_imr_v23_7_0_0029.7z
LSISAS2108, v12.12.0-0111, merged, CC Pro 2.0 supported
lsi_raid_megaraid_fw_lsisas2108_imr_v12_12_0_0111.7z
LSISAS2008, v20.10.1-0101
lsi_raid_megaraid_fw_lsisas2008_imr_v20_10_1_0101.7z
這三款都不會有DS3支持, 目前暫時一段時間都不會支持DS3...

作者: per1-q1222 时间: 2012-6-13 08:14
本帖最后由 per1-q1222 于 2012-6-13 08:17 编辑

About DS3 function:
LSI Request :: P00046621
the LSI MegaRAID controllers currently have disabled support the DimmerSwitch. There is no ETA for when this feature will be supported again.

作者: jimmyjin 时间: 2012-6-13 14:11

per1-q1222 发表于 2012-6-13 08:14
About DS3 function:
LSI Request :: P00046621
the LSI MegaRAID controllers currently have disabled ...

继续悲催啊......

作者: nikon_d3x 时间: 2012-6-13 17:32
2108和2208修正了什么？

作者: per1-q1222 时间: 2012-6-13 18:12
本帖最后由 per1-q1222 于 2012-6-13 18:13 编辑

nikon_d3x 发表于 2012-6-13 17:32
2108和2208修正了什么？

這是從IBM那邊的..
所以是針對IBM的ServeRAID為主..

我並不清楚詳細修正有那些...

作者: per1-q1222 时间: 2012-6-16 22:14
本帖最后由 per1-q1222 于 2012-6-16 22:14 编辑

LSISAS2208 changelog:
Version 23.7.0-0029 - Suggested
-------------------
Enhancements:
- Added support for Cache Cade 2.1
- Added Support for PI Drives

Fixes

- Fixed an issue where the firmware reports device initialization completion status to
be greater than 100% at startup.
- Fix an issue where when a secure foreign drive was present, VD creation fails because
firmware becomes unresponsive
- Added a check for the presence of PD before writing the data arms of a protected LD
during BGI.
- Fixed Firmware asserts in CacheMemAllocForPrebootApps() when memory was allocated
twice by BIOS.
- Fixed an issue with USB Cacheoffload restore fails after multiple power cycles on
ServeRAID M51xx controllers.
- Fixed an issue where querying SMART / PFA Status returns ?ll zeros?in Sense Data.
- Fixed an issue where the import of a config from MR to iMR resulted in a firmware crash.
- Fixed an issue where iMR firmware crashed while creating 8/16/32 KB stripe size Lds.
- Fixed background initialization watermark conversion to PD LBA.
- Fixed write protected R1E data arms during initialization.
- Fixed an issue where MR firmware crashed while discarding pinned cache.
- Fixed an issue where a dirty LD dependency information of SSD pd has stale entries.
- Corrected an issue during system booting from pinned cache, firmware goes to loop
message BootMsgDcmd
- Fixed an issue where a BGI was aborted and restarted, elapsed time was not reset.
- Fixed an issue where the start ref for a shared cache line was not an indicator of
the offset into the stripe.
- Fixed an issue where the firmware hangs while running CC on a rebuilt R1 VD with SBBM.
- Fixed an issue where the firmware was wrongly adding puncture entries.
- Fixed an issue where rebuild was ran twice on a target drive with 100% full SBBM table.
- Fixed an issue where the firmware was generating powersave change event when DS3 was
not enabled, due to this application are not parsing the event.
- Fixed an issue where recon from R0 to R1 using 3 TB drive causes firmware to report
excessive unexpected sense events.
- Fixed an issue, in which the bbuMode would revert to the factory default value of 5,
when automatic learn cycle was enabled.
- Fixed an issue where cache offload firmware reports unnecessary High Temp Event due
to incorrect temp value.
- Fixed an issue in which a Patrol Read may not start under certain conditions.
- Fixed an issue where the firmware hits montask after discarding the cache when a
snapshot VD was involved.
- Fixed an issue where the firmware hangs during pin cache destage as dirty lines in
that map never become zero.
- Fixed an issue where CC fails to correct media error at 2TB location on 2 3TB SATA
drives that support WU.
- Fixed an issue where a new XML file was added to the nvdata, the buffer to hold the
uncompressed nvdata overflowed.
- Fixed an issue where an imported drive becomes unconfigured good when secure VD
erase was running.
- Fixed an issue where CC stops progressing on a R6 VD with media errors.
- Fixed an issue where 3TB Hitachi HDD failed in immunity test (Electrostatic Noise
test).
- Fixed an issue where controller features are lost if RAID Key was not detected
- Fixed an issue where performance degraded in RAID 5 Sequential Writes due to
command Out-of Ordering.
- Fixed an issue where ?ative configuration is no longer supported?message in post.
- Fixed an issue where (DDR3) Initialization fails with fault 0x91a1 - initial DFIRL
selected too low.
- Fixed an issue where subsequent drives are dropped when all drives in the stagger
spin up drives fails on boot sequence.

作者: per1-q1222 时间: 2012-6-16 22:16
Driver changelog:
Version 5.2.12 - Suggested
--------------
Fixes
- Fixed an issue while updating Win2k8x32 driver the user will get the following error
"This device can not start (Code 10)." message
- Fixed an issue where MSM 12.01.03.00 alerts are not giving proper windows version.
- Fixed an issue where the driver was setting the region lock type even when firmware
informs driver to bypass lock.
- Fixed Sequential Write performance
- Fixed an issue where I/Os stop sporadically with outstanding I/Os.
- Changed the behavior of the driver to not send srb flush down by default; it
manually checks the inf file for the device ids or on a system with these devices.
- Fixed an issue where Windows LSI Driver megasas2.sys has inconsistent File version.

作者: per1-q1222 时间: 2012-6-19 06:54
本帖最后由 per1-q1222 于 2012-6-19 06:54 编辑

official changelog for driver:
Changes from version 5.2.125 to 5.2.127.
1)SCGCQ00280848             Updating Win2k8x32 & Vistax32 driver from 5.2.119 to 5.2.125 fails with "This device can not start (Code 10)." message

Changes from version 5.2.124 to 5.2.125.
1)SCGCQ00278761             Huawei device 0x2208 added to Windows driver supported list
2)SCGCQ00260160             MSM 12.01.03.00\Alerts are not giving proper windows version.

Changes from version 5.2.119 to 5.2.124.
1)SCGCQ00243559             Driver setting the region lock type even when FW informs driver to bypass lock
2)SCGCQ00268839             SuperMicro device ID C690 should be 0690
3)SCGCQ00264491             512e drive support for MR Windows Driver
4)SCGCQ00269250             New device IDs

Changes from version 5.2.116 to 5.2.119.
1)SCGCQ00261879             DIF support for Thunderbolt MR controllers
2)New Devices added
      SCGCQ00261881       Add PnP for CC enabled 8-port Thunderbolt D1 SKU
      SCGCQ00261883       Add PnP for CC enabled 8-port ext. Thunderbolt D1 SKU

Changes from version 5.2.112 to 5.2.116.
1)SCGCQ00255185       Sub device 0xD204 of sub vendor 0x19E5 missing
2)SCGCQ00252665             Driver 5.2.112 megasas2.inf file is missing SSDID - 92A0,92A1
3)SCGCQ00250757             TB Windows driver : Sequential Write performance drops significantly.
4)SCGCQ00247489             IOs stop sporadically with outstanding IOs.
5)SCGCQ00246917             With 5.2.112, wrong version display with "msinfo32"
6)New Devices added
      SCGCQ00248658       2208 MROMB Design Asustek - Pike-2208 Program
      SCGCQ00249402       Catera MantaRay
      SCGCQ00249403       Catera Shikra
      SCGCQ00249405       MR 2208 MROMB PnP IDs --  Gigabyte
      SCGCQ00249406       Quanta will implement MR 2208 RAID stack embedded for LSI 2208

作者: 江峰 时间: 2012-6-25 15:02
感谢楼主的分享。

欢迎光临 POPPUR爱换 (https://we.poppur.com/)