POPPUR爱换

标题: 【分享】在普通PC主板上就能使用的PCIE接口的SATA RAID卡 [打印本页]

作者: Robin_Zhang    时间: 2008-4-14 20:00
标题: 【分享】在普通PC主板上就能使用的PCIE接口的SATA RAID卡
国内媒体很少报道和提供同类产品的测评,国内玩家也很少接触这样的产品。这里笔者做一个简单的介绍。
Areca
ARC-1210/1220/1230/1260
(4/8/12/16-port PCIe to SATA ll RAID Adapters)


ARECA PCI-Express RAID Card Comparison
Model Name
ARC-1210
ARC-1220
ARC-1230
ARC-1260
RAID Processor
IOP332
IOP333
Host Bus Type
PCI-Express X8
RAID 6 Support
N/A
YES
YES
YES
Cache Memory
256MB
256MB
One SODIMM
One SODIMM
Driver Support
4*SATA ll
8*SATA ll
12*SATA ll
16*SATA ll

Adapter Architecture
  
ARC-1210 uses IntelR IOP332 I/O processor. ARC-1220/1230/1260 uses IntelR IOP333 I/O processor
   PCI-Express X8 bus
   256MB on-board DDR333 SDRAM with ECC protection(4/8-port)
   One SODIMM socket with default 256MB of DDR333 SDRAM with ECC protection, Upgrade to 1GB. An ECC or non-ECC SDRAM module using X8 or X16 chip organization (12/16/24-port)  
   Write-through or write-back cache support
   Support up to 4/8/12/16 SATA II drives
   Multi-adapter support for large storage requirements
   BIOS boot support for greater fault tolerance
   BIOS PnP (plug and play) and BBS (BIOS boot specification) support
   Intel RAID 6 Engine to support extreme performance RAID 6
   NVRAM for RAID event & transaction log  
   Redundant flash image for adapter availability  
   Battery Backup Module (BBM) ready
ARC-6120BA-T1xx, xx means version no.
   RoHS Compliant  
   
  RAID Features
   RAID level 0, 1, 1E, 3, 5, 6 (if RAID 6 engine supported) and JBOD
   Multiple RAID selection
   Array roaming
   Online RAID level/stripe size migration  
   Online RAID capacity expansion and RAID level migration simultaneously
   Instant availability and background initialization
   Automatic drive insertion/removal detection and rebuild
   Greater than 2TB per volume set  
   Support S.M.A.R.T, NCQ and OOB Staggered Spin-up capable drives
   Support spin down drivers when not in use to extend service life (MAID)  

      
  Software Drivers
   Windows 2000/XP (Scsiport Driver)
   Windows Server 2003 (Scsiport Driver and Storport Driver)  
   Redhat Linux and SuSE Linux  
   FreeBSD
   Solaris 10x86
   UnixWare 7.1.x
   Netware 6.5

[ 本帖最后由 Robin_Zhang 于 2008-4-14 20:43 编辑 ]
作者: Robin_Zhang    时间: 2008-4-14 20:04
Promise
SuperTrak EX8350


SuperTrak EX8350 Highlights

8-Port Serial ATA (SATA) RAID controller with 3.0 Gb/s per port
PCI-Express x 4 Host Bus Interface
Support RAID levels 0, 1, 5, 6, 10, 50 and JBOD
Linux open source driver support
Online capacity expansion and RAID level migration to add capacity as needed
Hardware- accelerated RAID 6 Capable for maximum reliability
Intel IOP333 XScale® I/O processor
Multiple logical drive support
Automatic/manual rebuild of hot spare drive
PerfectRAID technology for robust error handling and recovery
Battery backup module optional

Controller Specifications

Eight SATA ports at 3.0Gb/s (300MB/sec)
Storage capacity up to 16.0 terabytes (with eight 500GB drives x 4 controllers/ system)
PCI-Express x 4 host bus interface
Intel IOP333 XScale® I/O processor (500 MHz)
128MB DDR ECC on-board controller cache
Battery back-up module option
Four controller support within a system
Low profile form factor ideal for 1U/2U server
Combine with the SuperSwap 4100 for an advanced internal storage system
RAID Levels Supported

RAID 0, 1, 5, 6, 10, 50 and JBOD

Operating Systems

Microsoft Windows 2000/XP/2003
Red Hat Linux, SuSE Linux, Linux open source driver

[ 本帖最后由 Robin_Zhang 于 2008-4-14 20:23 编辑 ]
作者: Robin_Zhang    时间: 2008-4-14 20:05
AMCC
3ware 9650SE



Model9650SE-2LP9650SE-4LPML9650SE-8LPML
Form Factor Low Profile Low Profile Low Profile
Port Count248
PCI Express Lanes 144
Raid Levels 0,1, Single Disk,JBOD 0,1,5,10,Single Disk,JBOD0,1,5,6,10,50,Single Disk,JBOD
Onboard Memory128 MB DDR2 533 256 MB DDR2 533 256 MB DDR2 533
Connector TypeDiscreteMulti-laneMulti-lane
BBU Support NoYesYes

Model9650SE-12ML9650SE-16ML9650SE-24M8
Form Factor Full Height Full Height Full Height
Port Count121624
PCI Express Lanes 888
Raid Levels 0,1,5,6,10,50 Single Disk,JBOD 0,1,5,6,10,50,Single Disk,JBOD0,1,5,6,10,50,Single Disk,JBOD
Onboard Memory256 MB DDR2 533 256 MB DDR2 533 512 MB DDR2 533
Connector TypeMulti-laneMulti-laneMulti-lane
BBU Support YesYesYes
* All models are RoHS Compliant


3ware 9650SE Features

8th-generation StorSwitch™ non-blocking switched architecture.
On-board I/O RISC processor and RAID offload provides true hardware RAID.
- SCSI device driver model to take advantage of the benefits of SCSI using inexpensive Serial ATA drives .
Bootable array support for greater fault tolerance.
Variable stripe size for performance tuning by application.
64-bit LBA support.
ATA pass-through mode support.
Up to 512MB DDR2 533 memory with ECC protection. (see table below)
32 pooled DMA channels.
Complete configuration management suite.
- 3ware BIOS Manager 2 (3BM2) – easy to use BIOS configuration tool.
- 3ware Disk Manager 2 (3DM®2) – browser-based management tool.
- Command Line Interface (CLI) – scriptable configuration tool.
SNMP support.
SMTP support for email/pager notification.
ATA/6 and Out of band (OOB) staggered drive spin-up support.
Auto carving allows LUNs > 2TB to be divided into multiple units for legacy operating systems limited to 2TB max. per LUN.
Battery Backup Unit (BBU) support.
Multiple logical unit sizes and RAID levels on one card.
Multiple card support within a system for large storage requirements.
Hot-swap and hot-spare support for data availability.
Dynamic sector repair for robust data protection.
S.M.A.R.T. disk drive monitoring for reliability.
Emergency Flash Recovery protects against failed firmware upgrade.
Drive activity LED support.
Online Capacity Expansion and RAID Level Migration.
Enhanced data protection with write journaling for non-redundant arrays and accidental drive removal.
Drive insertion and removal notification.
Array/Drive Status and drive identification LED support. (requires 3ware Chassis Control Unit-enabled backplane)
Chassis Control Unit for enclosure management via I2C.
Operating System Support

Microsoft® Windows® 2003/XP/2000, Red Hat Linux, SuSE Linux, Fedora Linux, 2.4 Linux kernel, 2.6 Linux kernel, FreeBSD; 32/64-bit driver support for Windows, Linux and FreeBSD For complete OS listing, Go to: www.3ware.com/support/OS-Support.asp

[ 本帖最后由 Robin_Zhang 于 2008-4-14 20:24 编辑 ]
作者: Robin_Zhang    时间: 2008-4-14 20:09
LSI
MegaRAID SATA 300-8ELP


Benefits
Internal SATA ports (8)
x4 SFF-8087 connectors (2)
3 Gb/s throughput per port
RAID levels 0, 1, 5, 10 and 50
Greater than 2TB array support
Intel® IOP333 I/O Processor
PCI Express 1.1 compliant
2.5 Gb/s per lane
x4 lane width
128MB DDR 333 MHz SDRAM on board
Remote intelligent BBU (LSIiBBU01) option
Advanced data integrity and recovery
Enhanced error handling and reporting
Online capacity expansion (OCE)
Online RAID level migration (RLM)
Comprehensive management and configuration utilities
SAS expander support
(16-disk support)

[ 本帖最后由 Robin_Zhang 于 2008-4-14 20:25 编辑 ]
作者: Robin_Zhang    时间: 2008-4-14 20:10
Highpoint
RocketRAID 2320 Host Adapter


Controller Specifications
PCI Express x4
SATA II and SATA I hard drive support
Up to 300MB/s for each SATA II drive port
Support RAID level 0, 1, 5, 10 and JBOD
Dynamic Sector Repair and Remapping
Online Capacity Expansion and Online RAID Level Migration (OCE/ORLM)
Native Command Queuing (NCQ)
SAF-TE enclosure management
Hard drive activity and Failed LED support
Staggered drive spin-up support
Hot swap and hot spare
Write-through and write-back cache support
Quick and Background initialization for quick RAID configuration
Online array roaming
BIOS booting support (INT13)
Single RAID Cross Adapter Support
64bit LBA for over 2TB support
Automatic RAID rebuild of failed drive
S.M.A.R.T drive monitoring for status and reliability
Browser-based RAID management software
Command Line Interface (CLI)
SMTP for email notification
Operating system support for Windows, Windows x64 Editions Linux (open source), FreeBSD (open source) and Mac OS X
RAID Management Utilities
BIOS
Browser-based RAID Management
CLI
Operating Systems

Windows, Windows X64 Editions, Linux(opensource)
FreeBSD(opensource) and Mac OS X

[ 本帖最后由 Robin_Zhang 于 2008-4-14 20:26 编辑 ]
作者: Robin_Zhang    时间: 2008-4-14 20:32
开始贴测试成绩:
RAID 0









[ 本帖最后由 Robin_Zhang 于 2008-4-14 20:36 编辑 ]
作者: Robin_Zhang    时间: 2008-4-14 20:39
RAID 0+1








作者: Robin_Zhang    时间: 2008-4-14 20:42
RAID 5








作者: kim.lee    时间: 2008-4-14 20:52
没参考价格:funk:

估计都价格不菲
作者: zjy315DOOM    时间: 2008-4-14 21:26
标题: 女侠,您帮了俺大忙了
俺现在有两个方案
方案一:价格便宜,不要求raid,只要求能接足够多硬盘,14-16个硬盘

方案二:要求有一定的性价比,组raid5,8-12个硬盘,最好能支持16个硬盘

俺初入此道,请女侠帮俺设计一下方案并提供一下大致价格,如果能在电源方面给以适当介绍就更好了

俺家用数据备份,应该属于阵发性开机:loveliness:
作者: Adamhe    时间: 2008-4-14 22:48
有sas的卡么? pci-e的.谢谢
作者: idolclub    时间: 2008-4-14 23:03
原帖由 zjy315DOOM 于 2008-4-14 21:26 发表
俺现在有两个方案
方案一:价格便宜,不要求raid,只要求能接足够多硬盘,14-16个硬盘

方案二:要求有一定的性价比,组raid5,8-12个硬盘,最好能支持16个硬盘

俺初入此道,请女侠帮俺设计一下方案并提供一下 ...

能支持14~16个硬盘的, 一般都是帶Raid 5功能. 你的預算是多少?
作者: Robin_Zhang    时间: 2008-4-15 08:43
原帖由 zjy315DOOM 于 2008-4-14 21:26 发表
俺现在有两个方案
方案一:价格便宜,不要求raid,只要求能接足够多硬盘,14-16个硬盘

方案二:要求有一定的性价比,组raid5,8-12个硬盘,最好能支持16个硬盘

俺初入此道,请女侠帮俺设计一下方案并提供一下 ...

可以考虑9650SE-16ML,它有备用电池……但是……价格会比较贵……你要有思想准备……
还有,你需要注意一般16口的RAID卡都需要PCIE 8X的插槽,你可以像我一样选择IGP主板并把卡插在PCIE16X上,或者选择975、X38这类主板,切忌选择NV的芯片组,和RAID卡很容易有冲突……
这是产品图样:



我还比较关心16块硬盘你拿什么机箱装……:sweatingbullets:
作者: 曦曦2006    时间: 2008-4-15 08:52
记号,学习一下...
作者: hh    时间: 2008-4-15 09:09
提示: 作者被禁止或删除 内容自动屏蔽
作者: ayuankawa    时间: 2008-4-15 09:18
提示: 作者被禁止或删除 内容自动屏蔽
作者: easternbp    时间: 2008-4-15 09:18
RAID春 RAID夏 RAID秋 RAID冬 :loveliness:
作者: zjy315DOOM    时间: 2008-4-15 20:45
标题: 回复 13# 的帖子
:loveliness: 女侠,俺是1022
3*4+2可以装14块硬盘
如果用5位的笼子,16块也没问题,不过可能通风效果要差些

9650SE-16ML多少米能拿下?
俺就是一个数据存储,对速度没太高要求

俺现在NF4U有8个串口,如果有8口的便宜卡,也凑活了

要是卡和N家兼通不好,可以考虑入块GX5,装在PCIe16X上
预算么,3K是俺可以接受的上限
作者: zjy315DOOM    时间: 2008-4-15 20:54
:funk: 女侠的卡价格有点夸张

而且电源也是困扰俺的一个因素
作者: idolclub    时间: 2008-4-15 21:14
原帖由 zjy315DOOM 于 2008-4-15 20:54 发表
:funk: 女侠的卡价格有点夸张

而且电源也是困扰俺的一个因素

好电源也不難找的.
作者: zjy315DOOM    时间: 2008-4-15 21:21
原帖由 idolclub 于 2008-4-15 21:14 发表

好电源也不難找的.


有16个sata电源接口的电源很好找么,价格亲善否
作者: fact88    时间: 2008-4-15 21:26
我想知道硬盘放在那里去?
作者: catalufa1984    时间: 2008-4-15 21:32
amd的芯片组行么?
作者: 双鱼不吃鱼    时间: 2008-4-15 21:34
思路上看到某人的机箱上24个硬盘的
作者: zjy315DOOM    时间: 2008-4-15 21:47
其实这个东西性价比还是满高的
http://www.century.co.jp/products/hd/ex35pm8bpe.html

可惜国内没有:(
作者: idolclub    时间: 2008-4-15 22:12
原帖由 zjy315DOOM 于 2008-4-15 21:21 发表


有16个sata电源接口的电源很好找么,价格亲善否

900~1000元內選擇也不少, 要不使用雙电源也可以.
作者: Larkin    时间: 2008-4-15 22:16
看了篇毒文,http://forum.coolaler.com/showthread.php?t=176664,上面那个3520性能如何?不过如果和680I不兼容地话,就当我什么都没有说吧...
作者: TOMCAN    时间: 2008-4-15 22:40
找12V 5V电流大的工业电源 做16个SATA口还是很容易的…… 只不过这么多硬盘外加供电,散热一定非常壮观了
作者: Robin_Zhang    时间: 2008-4-16 00:09
原帖由 Larkin 于 2008-4-15 22:16 发表
看了篇毒文,http://forum.coolaler.com/showthread.php?t=176664,上面那个3520性能如何?不过如果和680I不兼容地话,就当我什么都没有说吧...

他没有测试最重要的IOmeter……:shifty:
作者: jForce    时间: 2008-4-16 10:55
用780G或者790GX。可以CF的
插2个卡
16+ SATA接口搞定:devil:
作者: zjy315DOOM    时间: 2008-4-16 21:31
标题: 回复 30# 的帖子
俺不想用A,目前
作者: anti_alive    时间: 2008-4-17 15:41
主流的RAID卡关键看处理器,象3WARE这类卡用的处理器是基于IBM 授权的POWERPC 405架构的,它的吞吐和功耗都要比用INTEL XSCALE架构的IOP系列的U要好,其实不必去买那么贵的SATA RAID卡,论坛上大把的DELL PERC 5I,5E,6E(SAS RAID)性能都要比SATA RAID好,而且可以扩充缓存。SAS RAID卡可以支持SAS和SATA盘混插的。
PERC 5I是基于LSILOGIC 1068E SAS芯片和INTEL IOP 333的,IOP 333的主频是500MHZ,可以支持512M DDR2 ECC REG,或者1G DDR ECC REG。
PERC 5E是基于LSILOGIC 1078的单芯片(RAID ON CHIP),集成了一个基于IBM POWERPC 405架构的U(500MHZ),6E也是这个架构的,具体有什么改进不太清楚。
性能最好的当属HP的 P600,P800系列,集成的U是基于IBM POWER PC 440的,这颗U可是超级计算机用的U。
高端与否卡这卡是不是提供RAID 6支持,强劲的U在开启RAID 6的同时还能保持高的吞吐量,这是设计高端卡的初衷
作者: 我系高手!    时间: 2008-4-17 15:51
原帖由 anti_alive 于 2008-4-17 15:41 发表
主流的RAID卡关键看处理器,象3WARE这类卡用的处理器是基于IBM 授权的POWERPC 405架构的,它的吞吐和功耗都要比用INTEL XSCALE架构的IOP系列的U要好,其实不必去买那么贵的SATA RAID卡,论坛上大把的DELL PERC 5I,5 ...


呵呵,那些贵卡我就不奢望了,
反正现在perc5i便宜的很,比较值得买。
作者: 我系高手!    时间: 2008-4-17 15:55
perc5i真的可以用1g的缓存?
有人试过吗?
如果可以,我就买条回来,开写缓存就爽呆了:a) :a)
作者: anti_alive    时间: 2008-4-17 16:00
问题是现在5I上面的内存槽是 DDR2的,我写的很清楚:“支持1G DDR ECC REG,512M DDR2 ECC REG”
作者: shike_cuke    时间: 2008-4-17 17:23
好东西,,,硬RAID卡啊!
作者: 我系高手!    时间: 2008-4-17 19:28
原帖由 anti_alive 于 2008-4-17 16:00 发表
问题是现在5I上面的内存槽是 DDR2的,我写的很清楚:“支持1G DDR ECC REG,512M DDR2 ECC REG”


:wacko: 我还以为是你笔误呢,漏了个2
那看样子只能512m了
作者: Robin_Zhang    时间: 2008-4-18 08:56
哈哈……无视Dell的产品……这次买的MD3000上居然是LSI的贴牌东东……太垃圾了……:lol:
作者: wangchunboss    时间: 2008-4-18 09:39
提示: 作者被禁止或删除 内容自动屏蔽
作者: Robin_Zhang    时间: 2008-4-18 17:15
Promise 的东西还是不错6de ^只是怎么会这么便宜?
作者: wangchunboss    时间: 2008-4-18 19:44
提示: 作者被禁止或删除 内容自动屏蔽
作者: ricemi    时间: 2008-4-18 20:01
关注一下....这些8口的SATA卡跟主板上的SATA接口有什么优势啊..
作者: Robin_Zhang    时间: 2008-4-19 18:48
优势还是很明显的
作者: zyoka    时间: 2008-4-20 14:33
提示: 作者被禁止或删除 内容自动屏蔽
作者: xday2000    时间: 2008-4-20 14:47
用RAID卡是不是意味着必须放弃一个显卡槽:blink:
作者: aska    时间: 2008-4-22 09:02
留着 ,买的 时候参考




欢迎光临 POPPUR爱换 (https://we.poppur.com/) Powered by Discuz! X3.4