POPPUR爱换

标题: 谁能帮忙找下FUJITSU M2684TAU 540MB介绍 [打印本页]

作者: celeron1.5 时间: 2008-6-15 08:31
标题: 谁能帮忙找下FUJITSU M2684TAU 540MB介绍
找来个小硬盘，95年5月的，HD　TUNE测试正常，不支持SMART，MHDD也不能测，到正确检测到缓存，容量却是0。
搜不到M2684TAU的介绍，从搜来的富士通硬盘命名规则上看，只有开头的M能对上号，
M 在富士通的所有硬盘型号中固定在第一位. 是表示OEM产品的意思，其他对不上号。

作者: celeron1.5 时间: 2008-6-15 17:03
SF自己坐　　　

作者: Hakkinen98 时间: 2008-6-15 19:53
M 2 6 8 4 T A U FUJITSU
NO MORE PRODUCED                                     Native|  Translation
                                                   ------+-----+-----+-----
Form                3.5"/SLIMLINE       Cylinders 2379| 1024|    |
Capacity form/unform 528/    MB       Heads          6| 16|    |
Seek time / track  14.0/ 4.0 ms       Sector/track    | 63|    |
Controller          IDE / ATA2 FAST/ENHA  Precompensation
Cache/Buffer             KB             Landing Zone
Data transfer rate 4.200 MB/S int    Bytes/Sector    512
                  11.000 MB/S ext
Recording method    RLL 1/7                      operating  | non-operating
                                                -------------+--------------
Supply voltage    5/12 V    Temperature *C       5 50 | -45 60
Power: sleep             W    Humidity    %       20 80 |    5 95
   standby          W    Altitude km -0.300  3.000| -0.300 12.000
   idle             W    Shock       g       5    |    50
   seek             W    Rotation RPM    4500
   read/write       W    Acoustic dBA       43
   spin-up          W    ECC       Bit
                              MTBF       h    250000
                              Warranty Month
Lift/Lock/Park    YES       Certificates

Layout
FUJITSU M2681T/2682T/2684T JUMPER SETTING C141-E008-IM 1994

  +---------------------------------------------------------+
  |                                                       |XX I
  |                                                       |XX N
  |                                                       |XX T
  |                                                       |XX E
  |                                                       |XX R
  |                                                       |XX F
  |                                                       |XX A
  |                                                       |XX C
  |                                                       |XX E
  | +-+CN5                                              |XX
  | +-+                                                 |XX
  |                                                       |XX
  |                                                       |XX
  |                            +-CNH1                   |XX
  |                            | |                      |
  |                            | |                      |XX POWER
  |                            +-+                      |XX
  +---------------------------------------------------------+

Jumpers
FUJITSU M2681T/2682T/2684T JUMPER SETTING C141-E008-IM 1994

Jumper Setting
==============

x = Factory default

CNH1 1-2  Master/Slave
----------------------
x 1-2  CLOSED  Master drive
         OPEN Slave drive

CNH1 3-4  IORDY I/O Channel Ready signal to interface
-----------------------------------------------------
   3-4  CLOSED  IORDY connected to Host interface
x    OPEN IORDY is not connected to Host interface

CNH1 5-6  ACMODE signal to interface
------------------------------------
   5-6  CLOSED  ACMODE signal connected to Host interface all power
               safe commands executed normally
x    OPEN ACMODE signal is not connected to Host interface
               all power safe commands are ignored

CNH1 7-8  Automatic idle control
--------------------------------
   7-8  CLOSED  Automatic idle control is disabled
x    OPEN Automatic idle control is enabled

CNH1 9-10  Cable Select CSEL mode
---------------------------------
x 9-10  OPEN CSEL is not connected to Host interface normal mode
         CLOSED CSEL is connected to Host interface (Special cable
               needed)

CNH1 11-12 OPEN
----------------
OPEN DO NOT SHORT

CNH1 13-14 RESERVED
--------------------
CLOSED RESERVED!

General
FUJITSU => GDT

Tips & Hints about ICP controllers and other peripherals
========================================================

Tagged queues and Fujitsu M 26xx harddisks
------------------------------------------
Fujitsu Harddisks of the M26XX series do not support the SCSI-II
feature tagged queues. You should disable this feature in the
initialize disks menue of the GDTSetup program. An inquiry command
shows, that the harddisk supports tagged queues (this is why you can
enable it in the GDTSetup) but this is not true as stated by Fujitsu
Germany.

作者: sunnyd 时间: 2008-6-16 22:06
哈哈
以前有个富士通的 540M 硬盘，好多年前的80486上的
具体型号就不知道了

作者: celeron1.5 时间: 2008-6-17 17:00
谢谢3楼
是从文档上C+V来的吗，是的话能把文档发给我吗

作者: Hakkinen98 时间: 2008-6-18 22:31
http://stason.org/TULARC/pc/hard ... 5-SL-ATA2-FAST.html

作者: 93blue 时间: 2008-6-19 18:31
多少容量的？记得我以前有一块1G容量的富士通，一直能正常使用，后来被朋友拿去玩了

欢迎光临 POPPUR爱换 (https://we.poppur.com/)