|
本帖最后由 per1-q1222 于 2011-1-2 10:20 编辑
不解...
Seagate的SMART到底有沒有參考價值阿...
TW一堆人認為正常..
哪有幾天內ECC Recovered 就突破幾百萬的...
下面這個掃出來的運作也才13hrs左右(有人注意到SCTERC是supported的話, 那是我硬開的, 原本是沒有支援):
C:\>smartctl --scan-open
/dev/sda -d ata [ATA] (opened)
C:\>smartctl -a /dev/sda
smartctl 5.40 2010-10-16 r3189 [i686-w64-mingw32-win7(64)] (sf-win32-5.40-1)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.12 family
Device Model: ST31000528AS
Serial Number: 9VP9GLM4
Firmware Version: CC38
User Capacity: 1,000,204,886,016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Sun Jan 02 09:41:59 2011 TST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 609) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off supp
ort.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 182) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_
FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 111 100 006 Pre-fail Always -
31032389
3 Spin_Up_Time 0x0003 097 097 000 Pre-fail Always -
0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always -
10
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always -
0
7 Seek_Error_Rate 0x000f 100 253 030 Pre-fail Always -
20209
9 Power_On_Hours 0x0032 100 100 000 Old_age Always -
12
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always -
0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always -
5
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always -
0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always -
0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always -
0
188 Command_Timeout 0x0032 100 100 000 Old_age Always -
0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always -
0
190 Airflow_Temperature_Cel 0x0022 062 053 045 Old_age Always -
38 (Min/Max 20/39)
194 Temperature_Celsius 0x0022 038 047 000 Old_age Always -
38 (0 19 0 0)
195 Hardware_ECC_Recovered 0x001a 036 035 000 Old_age Always -
31032389
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always -
0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline -
0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always -
0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline -
59777354825750
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline -
3300788
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline -
631658510
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
|
|