|
|
一开始是不认SATA盘,用MegaCli -AdpAllInfo -aALL 查raid卡信息:
Adapter #0
==============================================================================
Versions
================
Product Name : PERC 6/i Integrated
Serial No : 1122334455667788
FW Package Build: 6.3.0-0001
Mfg. Data
================
Mfg. Date : 06/24/08
Rework Date : 06/24/08
Revision No :
Battery FRU : N/A
Image Versions in Flash:
================
FW Version : 1.22.12-0952
BIOS Version : 2.04.00
WebBIOS Version : 1.1-46-e_15-Rel
Ctrl-R Version : 1.02-015B
Preboot CLI Version: 01.00-023:#%00006
Boot Block Version : 1.00.00.01-0011
Pending Images in Flash
================
None
PCI Info
================
Controller Id : 0000
Vendor Id : 1000
Device Id : 0060
SubVendorId : 1028
SubDeviceId : 1f0c
Host Interface : PCIE
Link Speed : 0
Number of Frontend Port: 0
Device Interface : PCIE
Number of Backend Port: 8
Port : Address
0 0000000000000000
1 0000000000000000
2 0000000000000000
3 0000000000000000
4 0000000000000000
5 0000000000000000
6 0000000000000000
7 0000000000000000
HW Configuration
================
SAS Address : 50022190a4efab00
BBU : Present
Alarm : Absent
NVRAM : Present
Serial Debugger : Present
Memory : Present
Flash : Present
Memory Size : 256MB
TPM : Absent
On board Expander: Absent
Upgrade Key : Absent
Temperature sensor for ROC : Absent
Temperature sensor for controller : Absent
Settings
================
Current Time : 17:5:37 7/30, 2014
Predictive Fail Poll Interval : 300sec
Interrupt Throttle Active Count : 16
Interrupt Throttle Completion : 50us
Rebuild Rate : 30%
PR Rate : 30%
BGI Rate : 30%
Check Consistency Rate : 30%
Reconstruction Rate : 30%
Cache Flush Interval : 4s
Max Drives to Spinup at One Time : 2
Delay Among Spinup Groups : 12s
Physical Drive Coercion Mode : 128MB
Cluster Mode : Disabled
Alarm : Disabled
Auto Rebuild : Enabled
Battery Warning : Enabled
Ecc Bucket Size : 15
Ecc Bucket Leak Rate : 1440 Minutes
Restore HotSpare on Insertion : Disabled
Expose Enclosure Devices : Disabled
Maintain PD Fail History : Disabled
Host Request Reordering : Enabled
Auto Detect BackPlane Enabled : SGPIO/i2c SEP
Load Balance Mode : Auto
Use FDE Only : No
Security Key Assigned : No
Security Key Failed : No
Security Key Not Backedup : No
Default LD PowerSave Policy : Controller Defined
Maximum number of direct attached drives to spin up in 1 min : 0
Auto Enhanced Import : No
Any Offline VD Cache Preserved : No
Allow Boot with Preserved Cache : No
Disable Online Controller Reset : No
PFK in NVRAM : No
Use disk activity for locate : No
POST delay : 90 seconds
BIOS Error Handling : Stop On Errors
Current Boot Mode :Normal
Capabilities
================
RAID Level Supported : RAID0, RAID1, RAID5, RAID6, RAID00, RAID10, RAID50, RAID60, PRL 11, PRL 11 with spanning, SRL 3 supported, PRL11-RLQ0 DDF layout with no span, PRL11-RLQ0 DDF layout with span
Supported Drives : SAS, SATA
Allowed Mixing:
Mix in Enclosure Allowed
Status
================
ECC Bucket Count : 0
Limitations
================
Max Arms Per VD : 32
Max Spans Per VD : 8
Max Arrays : 128
Max Number of VDs : 64
Max Parallel Commands : 1008
Max SGE Count : 80
Max Data Transfer Size : 8192 sectors
Max Strips PerIO : 42
Max LD per array : 16
Min Strip Size : 8 KB
Max Strip Size : 1.0 MB
Max Configurable CacheCade Size: 0 GB
Current Size of CacheCade : 0 GB
Current Size of FW Cache : 0 MB
Device Present
================
Virtual Drives : 0
Degraded : 0
Offline : 0
Physical Devices : 0
Disks : 0
Critical Disks : 0
Failed Disks : 0
Supported Adapter Operations
================
Rebuild Rate : Yes
CC Rate : Yes
BGI Rate : Yes
Reconstruct Rate : Yes
Patrol Read Rate : Yes
Alarm Control : Yes
Cluster Support : No
BBU : Yes
Spanning : Yes
Dedicated Hot Spare : Yes
Revertible Hot Spares : Yes
Foreign Config Import : Yes
Self Diagnostic : Yes
Allow Mixed Redundancy on Array : No
Global Hot Spares : Yes
Deny SCSI Passthrough : No
Deny SMP Passthrough : No
Deny STP Passthrough : No
Support Security : No
Snapshot Enabled : No
Support the OCE without adding drives : No
Support PFK : No
Support PI : No
Support Boot Time PFK Change : No
Disable Online PFK Change : No
Support Shield State : No
Block SSD Write Disk Cache Change: No
Supported VD Operations
================
Read Policy : Yes
Write Policy : Yes
IO Policy : Yes
Access Policy : Yes
Disk Cache Policy : Yes
Reconstruction : Yes
Deny Locate : No
Deny CC : No
Allow Ctrl Encryption: No
Enable LDBBM : No
Support Breakmirror : No
Power Savings : No
Supported PD Operations
================
Force Online : Yes
Force Offline : Yes
Force Rebuild : Yes
Deny Force Failed : No
Deny Force Good/Bad : No
Deny Missing Replace : No
Deny Clear : No
Deny Locate : No
Support Temperature : No
NCQ : No
Disable Copyback : No
Enable JBOD : No
Enable Copyback on SMART : No
Enable Copyback to SSD on SMART Error : No
Enable SSD Patrol Read : No
PR Correct Unconfigured Areas : Yes
Error Counters
================
Memory Correctable Errors : 0
Memory Uncorrectable Errors : 0
Cluster Information
================
Cluster Permitted : No
Cluster Active : No
Default Settings
================
Phy Polarity : 0
Phy PolaritySplit : 0
Background Rate : 30
Strip Size : 64kB
Flush Time : 4 seconds
Write Policy : WB
Read Policy : None
Cache When BBU Bad : Disabled
Cached IO : No
SMART Mode : Mode 6
Alarm Disable : No
Coercion Mode : 128MB
ZCR Config : Unknown
Dirty LED Shows Drive Activity : No
BIOS Continue on Error : 0
Spin Down Mode : None
Allowed Device Type : SAS/SATA Mix
Allow Mix in Enclosure : Yes
Allow HDD SAS/SATA Mix in VD : No
Allow SSD SAS/SATA Mix in VD : No
Allow HDD/SSD Mix in VD : No
Allow SATA in Cluster : No
Max Chained Enclosures : 1
Disable Ctrl-R : No
Enable Web BIOS : No
Direct PD Mapping : Yes
BIOS Enumerate VDs : Yes
Restore Hot Spare on Insertion : No
Expose Enclosure Devices : No
Maintain PD Fail History : No
Disable Puncturing : No
Zero Based Enclosure Enumeration : Yes
PreBoot CLI Enabled : No
LED Show Drive Activity : No
Cluster Disable : Yes
SAS Disable : No
Auto Detect BackPlane Enable : SGPIO/i2c SEP
Use FDE Only : No
Enable Led Header : No
Delay during POST : 0
EnableCrashDump : No
Disable Online Controller Reset : No
EnableLDBBM : No
Un-Certified Hard Disk Drives : Block
Treat Single span R1E as R10 : No
Max LD per array : 16
Power Saving option : All power saving options are enabled
Default spin down time in minutes: 0
Enable JBOD : No
Time taken to detect CME : 60s
Exit Code: 0x00
发现:
Allow HDD SAS/SATA Mix in VD : No
Un-Certified Hard Disk Drives : Block
google一大圈没找到更改设置的命令,就想刷下最新6.3.3-0002试试,结果运行早就编辑好的刷固件批处理的时候,选了刷H310的megrec的cleanflash的那个批处理,cleanflash后看到提示重启了,运行m0flash就一直卡在
megaraid hwr contoller recovery tool,version 01.01-004 rebruary 05,2010
copyright 2006-2008 lsi corp.
supports 1078 controller and its successors.
setting up he chip for host-boot......
please do power cycle the host machine
please do not warm reboot by pressing (ctrl+alt+del)key
please make sure you removed the default jumper before you power on the system
-光标一直在这闪啊闪,
等了十几分钟看没反应,就出去吃饭,回来才发现,小区施工停电了,再开机试试这命令也一直卡在这了;
megarec -adplist查看:
...
megaraid hwr contoller recovery tool,version 01.01-004 rebruary 05,2010
copyright 2006-2008 lsi corp.
supports 1078 controller and its successors.
identified MR cards count:1
list of identified cards
----------------------------
MR Card 0
type:1078
vendor ID:0x1000,device ID:0x60
slot NO:2,device function:0x0
press a key to continue....
但是用MegaCli -AdpAllInfo -aALL已经认不到卡了:
......
copytight (c)supernar systems,LTD,1995-2002
dos/32a warning(9004):mouse initialization failed
F/W is in Fault state
Exit code:0x00
球大神指导,这卡还有救么? |
|
IP卡
狗仔卡
发表于 2014-7-30 19:08
QQ好友和群
收藏
分享
好贴
烂贴
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
显身卡
楼主
,怎么个操作法?serial boot rom么?