【不死心】还是那颗8400，还是那内存，还是那主板

杨三疯

今天又折腾了一晚上，我是彻底投降了~~~~~~~~

貌似一块硬盘也完蛋了~~~~~~现在认不出来那块硬盘了！问题不明！以后再说！



E8400在P5Q-E上死活最高就在420外频了~~~~倍频9.0，CPU电压加到1.5V，NB电压上到1.48，内存电压上到2.2，该开的都开了，该关的都关了，还是上不了450~~~~


网上看到黑金刚的800的条子都能跑上1000~~~~~，我现在想求一个能在WINDOWS下测试内存超频极限的软件~~~我不能再开机关机，2启会让我发疯的现在~~~最好也有测试CPU超频极限的工具~~~~~


实在要崩溃了~~~~~~~~~

yym

刷1101 或者1103 bios

yym

还有 切记 你的nB电压 别超过1.42  

P45特性就是电压越高越不能超。

我设置bios  你可以参照下 ：

JumperFree Configuration Settings
AI Overclock tuner: Manual
CPU Ratio Setting: 8 or 8.5
FSB Strap to North Bridge: auto
FSB Frequency: 500
PCI-E Frequency: 100
DRAM Frequency: 1200
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: Manual
1st Information :
CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 18
RAS# to RAS# Delay : A
Row Refresh Cycle Time: A
Write Recovery Time:A
Read to Precharge Time: A
2nd Information :
READ to WRITE Delay (S/D): A
Write to Read Delay (S): A
WRITE to READ Delay (D): A
READ to READ Delay (S): A
READ to READ Delay (D): A
WRITE to WRITE Delay (S): A
WRITE to WRITE Delay (D): A
3rd Information :
WRITE to PRE Delay: A
READ to PRE Delay: A
PRE to PRE Delay: A
ALL PRE to ACT Delay: A
ALL PRE to REF Delay: A
DRAM Static Read Control: e
DRAM Read Training: d
MEM. OC Charger: E
AI Clock Twister: A
AI Transaction Booster: Manual, or auto
Common Performance Level :
Pull-In of CHA PH1: DISABLED
Pull-In of CHA PH2: DISABLED
Pull-In of CHA PH3: DISABLED
Pull-In of CHA PH4: DISABLED
Pull-In of CHB PH1: DISABLED
Pull-In of CHB PH2: DISABLED
Pull-In of CHB PH3: DISABLED
Pull-In of CHB PH4: DISABLED
CPU Voltage: depends
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: 1.4（8X）  1.45（8.5×）
FSB Termination Voltage: 1.26
DRAM Voltage: 2.26
NB Voltage: 1.40-1.38
NB GTL Reference: AUTO
SBridge Voltage: 1.10V
PCIE SATA Voltage: 1.50V
Load Line Calibration: enable
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : 200
NB Clock Skew : 100
Advance CPU Settings
CPU Ratio Setting: Manual
CPU VID: Default
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Intel® Virtualization Tech: Disabled
Vanderpool Technology: Disabled
CPU TM Function: Disabled
Execute Disable Bit: Disabled


以上 我e3110 超4G与4.25G 设置 ，我用镁光原厂1066 1G×2 灯条

kof2003

{shy:] 我用技嘉的DS4p35没有2启现象

排骨饭

北桥1.42上500是指四核么？双核的话1.42貌似太高了~~~

windeye

先降倍频来测试外频吧

杨三疯

原帖由 排骨饭 于 2008-8-8 08:52 发表
北桥1.42上500是指四核么？双核的话1.42貌似太高了~~~

双核的话,北桥上多少比较合适?

杨三疯

原帖由 windeye 于 2008-8-8 08:55 发表
先降倍频来测试外频吧

试过了~~~~~~~CPU体质应该没多大问题~~~


现在我感觉就是内存条的问题,很拖累CPU,我内存只能跑到850,这个2.2V的电压下~~~~~

NETCARMEN

你那内存也太。。。了吧

找朋友借根神条试下不就知道瓶颈在哪里了吗

杨三疯

原帖由 NETCARMEN 于 2008-8-8 10:43 发表
你那内存也太。。。了吧

找朋友借根神条试下不就知道瓶颈在哪里了吗

呜呜呜呜呜,我性格很孤僻~~~没朋友~~~{wink:] {wink:]

windeye

原帖由 杨三疯 于 2008-8-8 10:33 发表



试过了~~~~~~~CPU体质应该没多大问题~~~


现在我感觉就是内存条的问题,很拖累CPU,我内存只能跑到850,这个2.2V的电压下~~~~~

两根内存条的话拔掉一根试试，也许有一根内存条强些的。

杨三疯

原帖由 mCore 于 2008-8-8 11:46 发表
初步鉴定，三疯现在已经彻底疯了。oc害人，电脑害人，PCI害人啊{titter:]

{lol:] {handshake:] {handshake:] {kiss:] {kiss:]

whhwhhwhh

原帖由 mCore 于 2008-8-8 11:46 发表
初步鉴定，三疯现在已经彻底疯了。oc害人，电脑害人，PCI害人啊{titter:]

{lol:] {lol:] {lol:] {lol:] {lol:] {lol:] {lol:]

riddick

你用500×6不就知道了～

杨三疯

原帖由 riddick 于 2008-8-9 11:18 发表
你用500×6不就知道了～

试过了，点不亮的~~~~~


能试的我都试了，现在99%是内存问题了！