|
本帖最后由 sonicxz 于 2010-7-10 21:55 编辑
帮LZ转些
http://www.right.com.cn/forum/vi ... xtra=page%3D1%26amp;orderby%3Ddateline
谢谢楼上朋友。
是按照一下这个教程刷DD-WRT:
Windows flashing instruction for the D-Link DIR-300 to DD-WRT (by Brainslayer, modified by Sash)
configure your local ip to 192.168.20.80
connect your lan cable to the WAN port of the router.
plugoff the power cord and replug it.
now enter the redboot using telnet and ip 192.168.20.81 and port 9000.
you might need several tries since its only available for 1 second after aprox. 5 sec. of booting
(in the appendix is a windows instruction for easy connecting to redboot)
DIR-300 Info:
IP: 192.168.20.81/255.255.255.0, Gateway: 0.0.0.0
Default server: 192.168.20.80
now start a local tftp server on your computer and place ap61.ram as well as ap61.rom in the root dir of this server
back to the redboot enter:
load ap61.ram
go
now a new temporarily bootloader should start. (on serial console it will display some warning. but you dont need to care about)
lug you lan cable to the lan port of the dir-300.
reconfigure your ip to 192.168.1.2 and connect via telnet to 192.168.1.1 and port 9000.
important: while doing the following steps. never plugoff the lan cable or the power cord
fis init
About to initialize [format] FLASH image system - continue (y/n)? y
*** Initialize FLASH Image System
... Erase from 0xbffe0000-0xbfff0000: .
... Program from 0x807f0000-0x80800000 at 0xbffe0000: .
ip_address -h 192.168.1.2
IP: 192.168.1.1/255.255.255.0, Gateway: 0.0.0.0
Default server: 192.168.1.2
load -r -b %{FREEMEMLO} ap61.rom
Using default protocol (TFTP)
Raw file loaded 0x80080000-0x800a8717, assumed entry at 0x80080000
fis create -l 0x30000 -e 0xbfc00000 RedBoot
An image named 'RedBoot' exists - continue (y/n)? y
... Erase from 0xbfc00000-0xbfc30000: ...
... Program from 0x80080000-0x800a8718 at 0xbfc00000: ...
... Erase from 0xbffe0000-0xbfff0000: .
... Program from 0x807f0000-0x80800000 at 0xbffe0000: .
reset
now the unit will reboot and the new bootloader will be executed and is waiting for your connection.
this wil take 30+ sec.
connect to the bootloader with telnet on port 9000 and ip 192.168.1.1
now do the following: (consider that fis create operations are taking sometimes several minutes to finish)
ip_address -h 192.168.1.2
load -r -b 0x80041000 linux.bin
fis create linux
fconfig boot_script true
fconfig boot_script_timeout 4
now type fconfig again and configure the bootscript to
fis load -l linux
exec
刷到这步后结束刷机,进不到192.168.1.1,又采取恢复原版固件
now type reset again. the unit should now boot dd-wrt and work as known from other atheros based platforms
-------------------------------------------------------------------------------------------------------------------
Appendix:
download putty.exe to c:
create a file an c: called redboot.bat with the following content:
rem echo off
:start
rem ------------------------------------------------
ping 192.168.20.81 -n 1 -w 1 > NULL
IF ERRORLEVEL 1 goto start
rem putty
rem ------------------------------------------------
break
putty.exe telnet://192.168.20.81:9000 -m redboot.txt
exit
create a file on c: called redboot.txt with the following content:
^C
start the bat file and power on the router.....here comes redboot
恢复原版固件参考这个教程:http://www.shadowandy.net/2007/1 ... iginal-firmware.htm
将网线插入LAN口,执行完以下步骤,只有电源灯再亮,挂了。
DD-WRT> ip_address -h 192.168.1.2
Default server: 192.168.1.2
DD-WRT> fis init
About to initialize [format] FLASH image system – continue (y/n)? y
*** Initialize FLASH Image System
… Erase from 0xbffe0000-0xbfff0000: .
… Program from 0x80ff0000-0×81000000 at 0xbffe0000: .
DD-WRT> load -r -b %{FREEMEMLO} dir300redboot.rom
Using default protocol (TFTP)
Raw file loaded 0×80040800-0x800607ff, assumed entry at 0×80040800
DD-WRT> fis create -l 0×30000 -e 0xbfc00000 RedBoot
An image named ‘RedBoot’ exists – continue (y/n)? y
… Erase from 0xbfc00000-0xbfc30000: …
… Program from 0×80040800-0×80060800 at 0xbfc00000: ..
… Erase from 0xbffe0000-0xbfff0000: .
… Program from 0x80ff0000-0×81000000 at 0xbffe0000: .
DD-WRT> reset
1.jpg (18.65 KB)
刷DD-WRT所用文件
2.jpg (15.67 KB)
恢复原厂固件使用文件
http://www.right.com.cn/forum/vi ... =1&extra=#pid256789
dir-300 Jtag接法
第一根是ntrst第二根是gnd第三根是tdi第五根是tdo第七根是tms
第九根是tck第十四根是vcc |
|
|