新产品 支持两块硬盘对拷 速度在60M/S左右,有兴趣的看看

sata_docking

Agestar S2BP多功能易驱 硬盘拷贝机支持硬盘对拷USB+eSATA输出



期待许久的产品，Agestar在2009年11月份全新推出的，功能强悍的易驱对拷设备，相信Agestar的多功能易驱线功能，其优秀的设计，出色的性能，良好的品质和做工已被国内众多用户所接收并喜爱，此次Agestar更是推出一款市面上，前所谓有的产品，目前该产品已申请多项全球专利，出色的性能表现，得益于Agestar强大的电子研发实力，此款易驱线S2BP的主控芯片以及PCB全部由台湾AGESTAR自主研发！

产品功能：
★直接挂裸盘，非常方便安装和移除硬盘
★支持USB2.0和高速eSATA口输出（接口采用最新的USB+eSATA复合端口）
★支持SATA到eSATA输出，速度可达3GPs/s
★支持SATA到USB2.0输出，速度可达480M/s
★支持SATA 1代/2代 2.5寸或是3.5寸硬盘
★支持一键盘份功能
★支持免PC，即脱机硬盘对拷功能
★电源支持AC100~240伏双认证电源，输出3A，支持2TB硬盘(特别说明一下，很多网友非常在乎于电流的安倍数，Agestar的电源都是3C认证正规电源，请不要同山赛产品的电源（标的虚高）相比，工厂都已经过严格测试后再出厂的，请各位买家放心)

硬盘对拷使用介绍：
S2BP另外一个强大的功能就是可以不通过电脑，而进行2个硬盘的对拷，当按下"备份"功能键5秒以后，产品上的2个硬盘就会开始对拷，拷贝的模式是从SATA1口上的来源硬盘copy到目标盘上，不可以反转，来源盘上的一切资料，包括操作系统，驱动程序，或是数据文件，影音文件，等一切硬盘数据，将会原封不动地copy到目标盘上，在拷贝过程中，易种上的LED灯会一直闪动，当LED完全停止闪动，则对拷工作完成！
有了此功能，不论您是广告从业者，影视编辑，还是摄影爱好者，或许您是高清电影爱好者，又或许是网络BT下载狂，您都可以非常方便地备份、分享您的资料，与朋友，同事轻松分享，不需要带电脑，只需要接上您的大容量硬盘，然后聊上一会天，您就可以带走您要的全部资料！
对拷注意事项：
★目标硬盘的容量必须大于或等于来源硬盘的容量，因为对拷是整盘复制的
★一旦对拷开始，目标硬盘上的一切资料将会被格式化掉，因此在对拷前请注意将目标硬盘上的资料先备份
★对拷动作可能会花费较长的时间，请耐心等待，LED没有停止闪烁，请不要随意关断电源或是取下硬盘！
★整个硬盘对拷的时间取决于来源硬盘的容量大小，同来源硬盘内实际资料文件的大小无关，如来源硬盘的容量为200G，以SATA2的对拷速度计算60M/S(3200M/分)
公式即为=  200000/3200=62.5分钟
（以上为实测大概估算时间，具体视环境而定）
★对拷时不需要通过电脑，也不需要使用USB和eSATA线，连接电源后，并连接好来源硬盘和目标硬盘后，按备份键5秒钟即开始对拷！
以下情况，在硬盘对拷图示，如果不符合要求，长按备份键后，将不会有红色灯闪烁，说明不支持硬盘对拷！

ffcuk

建议上实拍图，这种宣传图看了没一点安全感。

sata_docking

建议上实拍图，这种宣传图看了没一点安全感。
ffcuk 发表于 2009-11-4 18:46

嗯，实拍图如下，是用普通的卡片机拍的，拍的不是很好！但算真实吧

sata_docking

过几天，有空，我再上一些工厂的测试报告！

skytale

不用主机可以对拷?
分区也一样咯?

sata_docking

不用主机可以对拷?
分区也一样咯?
skytale 发表于 2009-11-4 20:05

是的，不需要电脑，将源盘插在SATA1口，将目标盘插在SATA2口，只需要接上电源，长按备份键按钮大约5秒种，对拷功能就会启动，开始对拷时，会把SATA2上的硬盘进行格式化，然后直接copy!

sata_docking

昨天晚上亲自在家用2个30G的硬盘试了一下，还不错，30G的，几分钟就搞定，一根烟还没有抽完！呵呵。

真知不易

可惜用不上，拷电影的方便了。

深港数码

可惜用不上，拷电影的方便了。
真知不易 发表于 2009-11-4 20:25

嗯，是的，拷电影呀，备份资料呀，素材呀，备份系统呀，DIY装机的人呀，这些都可以用到对拷功能！

同时对拷只是这个易驱线的一部分功能，它还可以连USB直接认到两个硬盘，支持WD 2T硬盘的，最大支持到4TB，也可以用eSATA高速copy，SATA2的硬盘，速度可以达到90M/S以上！

深港数码

老外也刚刚发布了，我们的速度比老外快两天呀，呵呵。。




We offer complete "software+hardware" drive back-up solutions and hardware drive cloning solutions

Worlds First Hardware Based SATA to SATA Drive Copy Adapter by CoolGear

NEW SS-126ASD Adapter with USB 2.0 and eSATA Back-Up Software for Windows XP/Vista/7 and Cloning One Button Press Feature

Supports all Makes and Models of SATA I/II/III Drives ranging in Capacity form 20GB up to 64TB

Cloning your hard drive could not be made any simpler!

Easy to install and remove the hard disk drive

COMBO USB 2.0 and eSATA input interface and Stand-Alone Disk Clone Feature

Support eSATA to Serial ATA interface,transfer rate up to 3.0Gb/sec

Support USB2.0 to Serial ATA interface,transfer rate up to 480Mb/sec

Suitable for 2.5"/3.5" Serial ATA HDD SATA I/II/II Compatible

One touch backup function

**Attached HDDs duplication function without PC system

Power supply: AC100~240V input,DC12V-3A output



Interface USB2.0/eSATA

Data transfer rate e-SATA to SATA I: 1.5G SATA II:3Gb/s ;USB2.0:480Mb/s

Suitability 2.5", 3.5" Serial ATA H.D.D(Available for 2 sata HDD same time)

Hardware requirement a PC,Notebook or Mac system with free USB or eSATA interface

Power 12V/3A Adapter

Material Plastic

Operation system Windows 2000/XP/Vista/7 and Mac OSX or above

Very Fast Sector Clone Feature Copies up to 100GB in 34 Minutes.



Works with all 3.5" SATA Desktop Drives



Works with all 2.5" SATA Laptop/NoteBook Drives Provides USB 2.0 Fast Data Transfer Port

Provides Ultra Fast eSATA 3Gbps Data Transfer Port

Quick User Guide PDF (click Here)

This Drive Copy Device can Clone any SATA 3.5" Drive as well as 2.5" of Any Capacity





This is a DO-IT-ALL HDD/SSD SATA Drive Adapter:

* it will back up your Computer files * it can move files extremely fast via USB 2.0 or even faster with eSATA port * it will help you with any Hard Drive Migration, Perfect for Laptop or Desktop Drives * it can Make DISK CLONE with Hardware Sector by Sector HDD Copy feature

This is a perfect companion for any Test Bench, Power User or Forensic Investigator as well as home user that simply has tons of data stored on many disks and needs a fast reliable disk copy/back-up solution.



Included in the Box:
1x Easy User Guide 1x USB 2.0 Cable 3ft. 1x eSATA Cable 3ft. 1x SATA HDD/Copier Device 1x eSATA Bracket (for your Motherboard) 1x SATA Drive Connection Cable (optional IDE PATA Drive Adapters avalable below) 1x Xp/Vista Back-Up Software 1x 3A 110/220Volt Power Adapter UL/FCC Listed 1x Power Cable for AC Adapter



Availability: Usually ships the next business day.

SS-126ASDRegular price: $44.98Sale price:

We offer complete "software+hardware" drive back-up solutions and hardware drive cloning solutions

Worlds First Hardware Based SATA to SATA Drive Copy Adapter by CoolGear

NEW SS-126ASD Adapter with USB 2.0 and eSATA Back-Up Software for Windows XP/Vista/7 and Cloning One Button Press Feature

Supports all Makes and Models of SATA I/II/III Drives ranging in Capacity form 20GB up to 64TB

Cloning your hard drive could not be made any simpler!

Easy to install and remove the hard disk drive

COMBO USB 2.0 and eSATA input interface and Stand-Alone Disk Clone Feature

Support eSATA to Serial ATA interface,transfer rate up to 3.0Gb/sec

Support USB2.0 to Serial ATA interface,transfer rate up to 480Mb/sec

Suitable for 2.5"/3.5" Serial ATA HDD SATA I/II/II Compatible

One touch backup function

**Attached HDDs duplication function without PC system

Power supply: AC100~240V input,DC12V-3A output



Interface USB2.0/eSATA

Data transfer rate e-SATA to SATA I: 1.5G SATA II:3Gb/s ;USB2.0:480Mb/s

Suitability 2.5", 3.5" Serial ATA H.D.D(Available for 2 sata HDD same time)

Hardware requirement a PC,Notebook or Mac system with free USB or eSATA interface

Power 12V/3A Adapter

Material Plastic

Operation system Windows 2000/XP/Vista/7 and Mac OSX or above

Very Fast Sector Clone Feature Copies up to 100GB in 34 Minutes.



Works with all 3.5" SATA Desktop Drives



Works with all 2.5" SATA Laptop/NoteBook Drives Provides USB 2.0 Fast Data Transfer Port

Provides Ultra Fast eSATA 3Gbps Data Transfer Port

Quick User Guide PDF (click Here)

This Drive Copy Device can Clone any SATA 3.5" Drive as well as 2.5" of Any Capacity





This is a DO-IT-ALL HDD/SSD SATA Drive Adapter:

* it will back up your Computer files * it can move files extremely fast via USB 2.0 or even faster with eSATA port * it will help you with any Hard Drive Migration, Perfect for Laptop or Desktop Drives * it can Make DISK CLONE with Hardware Sector by Sector HDD Copy feature

This is a perfect companion for any Test Bench, Power User or Forensic Investigator as well as home user that simply has tons of data stored on many disks and needs a fast reliable disk copy/back-up solution.



Included in the Box:
1x Easy User Guide 1x USB 2.0 Cable 3ft. 1x eSATA Cable 3ft. 1x SATA HDD/Copier Device 1x eSATA Bracket (for your Motherboard) 1x SATA Drive Connection Cable (optional IDE PATA Drive Adapters avalable below) 1x Xp/Vista Back-Up Software 1x 3A 110/220Volt Power Adapter UL/FCC Listed 1x Power Cable for AC Adapter

百事可乐

用这个备份的时候千万别把两个硬盘插反了

ffcuk

coolgear和agestar是什么关系啊？

lb0921

价格问题？、？

sata_docking

coolgear和agestar是什么关系啊？
ffcuk 发表于 2009-11-5 08:15

Agestar是 Coolgear的代工工厂！ Coolgear找Agestar做的贴牌

sata_docking

价格问题？、？
lb0921 发表于 2009-11-5 08:21

请到我们的TAOBAO店看一下:

http://agestar.taobao.com/

cushman

貌似不错 不知道传输安全性核准确行如何

dryfish

山寨气息浓郁啊。

井底牛蛙

这个新奇特啊！

sata_docking

山寨气息浓郁啊。
dryfish 发表于 2009-11-5 12:42

不知你认为什么是山寨？怎么定义的？

这是官网：www.agestar.com

itany

请问这个从小盘到大盘是怎么处理的？
建议楼主考察一下，比如我从1T到2T的，那2T剩下的空间咋办呢？