[HG281D]推荐一款显示器调节软件，不用为调节亮度对比度发愁了

eye2eye

原帖由 任性的猫 于 2008-12-11 09:12 发表
小心用啊！我的DELL1905已经乱了！怎么恢复到原厂设置呀？

老兄你的显示器可能已经无法调整回到正常状态了，除非返厂！！！！！！！！！！
下面是这个软件官方的警告！！！！！
http://www.nicomsoft.com/dtuner/warning.htm

Warning

A few users report about serious problems with their monitors. Some monitor manufacturers implement DDC control support in wrong way or use DDC bus for own purposes for some monitor models.When DTuner tries to read current monitor settings from such monitors according DDC standard theyrespond in wrong way. Also they can change some display settings that are not present in OSD and thereforeyou will not be able to change these settings back! Don't install DTuner if you don't need it really. In case of problems try to disconnect power cable from the monitor immediately for a minute, it may help to restoresettings. Try to use "Restore factory settings" command in monitor OSD. At this moment the following monitors models have serious problems with DTuner: LG Studioworks 563A LG StudioWorks 710E DELL 1905FP FLATRON EZ T710SH DTuner cannot restore monitor settings back for such monitors because it don't change them really,it only reads and sends standrard DDC command, if monitor change other settings it means this monitor is not compatiblewith DDC standard and its manufacturer implemented DDC support incorrectly. Such monitors can be even damaged by DTuner! Notphysically, but if manufacturer did not implemented "Restore factory settings" command in monitor OSD correctly andyou cannot access all monitor settings via OSD you will not be able to change settings back. Only a few such monitors were reported from hundreds thousand installations of DTuner, but you must be aware of such problem.

[ 本帖最后由 eye2eye 于 2008-12-12 06:07 编辑 ]

wuchen19820124

可怜，悲惨
这个软件实在害人啊

smty1111

看来还真有这回事，真得谨慎使用。

mm740

DELL1905正好上榜,怪lz没仔细考察!

thddr

NICE~
以前为SAMSUNG 226BW 找了很久~ 自家的Magic Tune 都不支持
没想到这个竟可以用！！ 多谢楼主  ~{lol:] 白深了两年胳膊

三星机器里的快捷方案是：
文本~亮度42 ~ 对比70
上网~   57  ~  75
游戏~   90  ~  80
运动~  100  ~  80
剧院~  100  ~  85
动态对比度~ 软件不予支持

供大家参考

[ 本帖最后由 thddr 于 2008-12-12 21:18 编辑 ]

mm740

原帖由 wuchen19820124 于 2008-12-12 18:59 发表
可怜，悲惨
这个软件实在害人啊

终于知道为什么vista认证规定要支持DDC/CI 1.1规范:loveliness:

mm740

原帖由 eye2eye 于 2008-12-12 18:56 发表


老兄你的显示器可能已经无法调整回到正常状态了，除非返厂！！！！！！！！！！
下面是这个软件官方的警告！！！！！
http://www.nicomsoft.com/dtuner/warning.htm


Warning



A few users report a ...

比LZ细心多了，这都能发现！:w00t):

newbier

很好用的软件，顶LZ和MM740一把{victory:]

ufo1cn

我的hg281D不能用报错说显示器不支持ddc-ci协议，可我在osd打开了ddc-ci啊，而且这时我装飞利浦的Altiris Philips Smart Manage Agent可以通过ddc-ci调亮度对比什么的

wuhao7926

本本液晶能用这个调节吗？？？？

PASS

台机281D可用,但我的本本就用不了。