和硕(华硕的子公司)给HP惠普代工的H61,型号IPXSB-DM,MINI-ITX主板,是HP HP p2-1400l Desktop PC系列型号的主机板,17*19 CM,采用H61芯片,支持35W的1155接口SNB,LVY的处理器,两条DDR3内存插槽,最大支持16G内存,带有2个SATA接口,DVI+VGA接口,是组建家庭影院,HTPC最佳选择,DC-19V供电。
主板是工厂库存货,成色近全新,有配挡板,和数据线和给硬盘供电的电源线,质保三个月。
主板支持以下处理器升级:
处理器
英特尔酷睿 i3-32xxT (Ivy Bridge) 双核
英特尔酷睿 i5-34xxT (Ivy Bridge) 双核
Intel 奔腾 G21xxT (Ivy Bridge)
英特尔酷睿 i3-21xx (Sandy Bridge) 双核
英特尔酷睿 i3-21xxT (Sandy Bridge) 双核
英特尔酷睿 i5-23xx (Sandy Bridge) 双核
英特尔奔腾 G4xx (Sandy Bridge) 单核
英特尔奔腾 G5xxT(Sandy Bridge) 双核
英特尔奔腾 G6xx (Sandy Bridge) 单核
英特尔奔腾 G6xxT (Sandy Bridge) 双核
Photograph of motherboard
[size=1.4em]Motherboard description
Manufacturer's motherboard name: Pegatron
Motherboard name: IPXSB-DM
HP/Compaq name: Cork
[size=1.4em]Form Factor
Mini-ITX : 17 cm (6.7 inches) x 19 cm (7.5 inches)
[size=1.4em]Chipset
Intel H61
[size=1.4em]Front-side bus speed
Not applicable
[size=1.4em]Processor upgrade information
Socket type: LGA 1155
Motherboard supports the following processor upgrades:
Celeron G440 (Sandy Bridge)
Celeron G530T (Sandy Bridge)
Core i3-2100T (Sandy Bridge) dual core
Pentium G6xxT (Sandy Bridge) dual core
[size=1.4em]Memory upgrade information
Dual channel memory architecture
Two 240-pin DDR3 UDIMM sockets
Supports DDR3 UDIMMs
PC3 8500 (1066 MHz)
PC3 10600 (1333 MHz)
Non-ECC memory only, unbuffered
Supports up to 4 GB on 32-bit* systems
Supports up to 16 GB on 64-bit systems (with 8 GB UDIMMs)
NOTE:
32-bit systems cannot address a full 4.0 GB of memory
[size=1.4em]Video
[size=1.4em]Intel PCH Integrated graphics
*Integrated video is not available if a graphics card is installed.
VGA port
DVI port
VGA and DVI ports can be used at the same time
[size=1.4em]Audio
[size=1.4em]Integrated Realtek ALC662 Audio
*Integrated audio is not available if a sound card is installed
6 channel audio
Realtek ALC662 CODEC
[size=1.4em]Network
[size=1.4em]LAN: 10-Base-T
Technology: Atheros AR8152 ethernet controller
Data transfer speeds: up to 10/100 Mb/s
Transmission standards: 10-Base-T Ethernet
[size=1.4em]I/O Ports
[size=1.4em]Back I/O ports Figure 2: Back I/O panel
[size=0.9em]1 - DC power
[size=0.9em]2 - DVI-D port
[size=0.9em]3 - VGA port
[size=0.9em]4 - LAN
[size=0.9em]5 - USB 2.0: 4
[size=0.9em]6 - Audio: Line in
[size=0.9em]7 - Audio: Line out
[size=0.9em]8 - Audio: Microphone
[size=1.4em]Internal Connectors
1x CPU fan connector
1x System fan connector
2x SATA connectors
2x SATA power connectors
2x USB 2.0 connectors
1x Front panel audio connector
1x ROM recovery connector
1x Front panel connector
[size=1.4em]Clearing the CMOS settings
CAUTION:
Do not change any jumper setting while the computer is on. Damage to the motherboard can result.
This motherboard has a jumper to clear the Real Time Clock (RTC) RAM in CMOS.
Turn OFF the computer and unplug the power cord.
Move the jumper to from pins 6-4 (default) to pins 4-2 for 5 to 10 secs, then move the jumper back to default.
Plug the power cord and turn ON the computer.
During the start-up process, enter BIOS setup to re-enter user settings
[size=1.4em]Clearing the PASSWORD settings
The BIOS password is used to protect BIOS settings from unwanted changes.
To erase the BIOS password follow these steps:
Turn OFF the computer.
Move the jumper to Clear from pins 5-3 (default) to pins 3-1.
Turn ON the computer to POST screen.
Turn OFF the computer.
Move the jumper back to default.
Enter BIOS setup to verify or configure new settings.