EP45-UD3R的内存问题。高手进来解答啊。

sagacity

上月入手。用GIKSLL 1000 2G*2 E84 一直稳定在 500*8下。从本周一开始。进系统就不短的死机。没有运行任何程序。降频后正常。降到450*8.反复测试后得知是内存问题。用SP2004 着重U没问题 着重内存 10秒内准报错。内存拿去换新，就又找了两条神条默电上1000那种。可是联450外频都进不去 参数都调到6-6-6-18了。只能稳定在430外频。可是在别的机器上1000@1.9 5-5-5-15 没有任何问题。OR过1小时。会不会是我的主板有问题了呢？内存插槽有问题了？高手进来看看吧。谢谢。

sagacity

自己顶一把

sagacity

论坛还真是冷清啊~~~~

srw0118

BIOS怎么设置的啊 刚入这块板 还没有上机

sagacity

把主要的几项都手动了 其他自动  已经稳定了 半个月了。就是前天突然开始不稳。感觉和BIOS设置没啥关系啊。

klinsmn

对症抓药 填张表先
- N: v+ N6 E1 E
*************************************************
" o) g4 p# x. C8 Z* BRobust Graphics Booster [XXXXX]
5 [% X( u' T3 p! x6 HCPU Clock Ratio[XXXXX]
$ J, s# \0 D, S0 m5 F% M7 [- cFine CPU Clock Ratio [XXXXX]
: K; Z+ |& P! r& V' X
**********Clock Chip Control*************************

( ]: n" V7 G: rCPU Host Clock Control [XXXXX]
" ~3 t9 C/ ~% k8 R+ hCPU Host Frequency (Mhz) [XXXXX]
PCI Express Frequency (Mhz) [XXXXX]
C.I.A 2
6 h$ H% q- f2 Z7 G5 `) J  U% E
: c) O% C2 w- n0 e+ X# a9 U5 b+ F% \*********Advanced Clock Control**********************

CPU Clock Drive [XXXXX]
9 k8 J' c& q- o. h* Z# I# qPCI Express Clock Drive [XXXXX]
CPU Clock Skew [XXXXX]
MCH Clock Skew [XXXXX]

**********DRAM Performance Control***********
% `. G$ k9 t2 y" \+ I/ R: S) C
Performance Enhance [XXXXX]
Extreme Memory Profile (XMP) [XXXXX]
+ Q0 s7 ?; J% x7 `(G) MCH Frequency Latch [XXXXX]
System Memory Multipler [XXXXX]
% v. `5 T8 O+ S8 Y! X* E% ]$ kMemory Frequency [XXXXX]
DRAM Timing Selectable [XXXXX]

CAS Latency Time [XXXXX]
2 F+ R, o4 V6 _tRCD [XXXXX]
tRP [XXXXX]
, q# A) u, y4 T+ H2 qtRAS [XXXXX]

) Z. _! M- }4 _7 Q; y0 s*******Advanced Timing Control***********

tRRD [XXXXX]
tWTR [XXXXX]
tWR [XXXXX]
  t! ?: ?9 [- K. g2 vtRFC [XXXXX]
tRTP [XXXXX]
% [" T3 }% w& M6 P% ^5 QCommand Rate (cmd) [XXXXX]
* U5 k+ B8 k1 R% m7 P! T3 K( W
5 ]" Y% a7 e7 c0 B4 c$ A! C
***********Motherboard Voltage Control*******
: r6 R9 B3 l$ x
Load-Line Calibration [XXXXX]
8 q/ o: z7 }: R9 O) lCPU Vcore [XXXXX]
CPU Termination [XXXXX]
CPU PLL [XXXXX]
CPU Reference [XXXXX]
4 Z, ]7 @; b  ]* l" _. K, x7 b4 e- N% [
MCH Core [XXXXX]
MCH Reference [XXXXX]
' y2 i5 E: V, {# R, Q/ ]MCH/DRAM Refernce [XXXXX]
ICH I/O [XXXXX]
2 z3 X4 U; f; V/ c0 p  C5 w# kICH Core [XXXXX]

- a8 b8 J* I. A9 ]0 o" ~DRAM Voltage [XXXXX]
3 q. T; [9 e3 }/ y3 a. cDRAM Termination [XXXXX]
/ b2 Y6 o- b+ H" WChannel A Ref [XXXXX]
; V1 @# ^$ H3 `* x8 O' Y# w! B3 wChannel B Ref [XXXXX]

*****************Advanced BIOS Features*********
2 O/ @$ n6 j( G9 Q1 n3 x
3 ?& y. A: H$ i& k  HCPU Multithreading [XXXXX]
Limit CPUID Max to 3 [XXXXX]
# D3 m) {, y0 X5 t* I) g  KNo-Execute memory Protect [XXXXX]
CPU Enhance Halt (CIE) [XXXXX]
C2/C2E State Support [XXXXX]
" q3 d' \2 A2 W$ S8 A; jC4/C4E State Support [XXXXX]
6 Y& [  c: P( `/ X  C) z& vCPU Thermal Monitor [XXXXX]
CPU EIST Function [XXXXX]
# |' O. t" B& t9 w2 g4 ~Virtualization Technology [XXXXX]

mdfree

我是EP45-UD3P
所以设计应该差不多
我也是用E84和Gskill的RAM 4G 2*2G 1066 5-5-5-15
+ M8 K' @, H7 G( r; t) V6 H按照Gskill讲 1066要加到2.1V
/ r+ D3 ]& p9 _: w我不知道你1000的要多少 估计也是要2.0-2.1V附近 1.9V会不会太低了

king30

老牛的Gskill的RAM 4G 2*2G 1066 5-5-5-15
我1.8V就8G  1066  5-5-5-15稳定了

klinsmn

不用猜了 是LZ的散热器没注意压坏北桥了 送修中
& E5 N" |1 [7 T9 E5 h, }1 u  D可怜的人