有用X38DQ6+E0版的Q9550超频的兄弟进来下

alexyin1984

U升级E0的Q9550，结果就碰到国外这老兄的问题了。完全无法超频。

http://forums.tweaktown.com/f69/problems-q9550-e0-x38-dq6-31140/

我这里情况是默电。设置仍然按之前E6750超3.6g的那样。

CPU Enhanced Halt (C1E)................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Disabled]
CPU EIST Function.........................: [Disabled]

Robust Graphics Booster___________ [Auto]
CPU Clock Ratio ___________________[8]
Fine Clock Ratio ___________________[0.5]
CPU Host Clock Control_____________ [Enabled]
CPU Host Frequency (MHz)__________ [350]
PCI Express Frequency (Mhz)________ [AUTO] (试过 100，101)
C.I.A. 2__________________________ [Disabled]
Performance Enhance ______________[Standard] (tried turbo, and extreme)
System Memory Multiplier (SPD)______ [2.0B] （自己内存之前一直在跑1080，这次为了排除内存问题，降频率了）
Memory Frequency_________________  700


Loadline Calibration_________________[Disabled](AUTO,Enabled都试过)


BIOS试过F9F，F8，甚至互刷过X48DQ6的F8C。情况都一样。

开始第一颗U在店里没试，拿回家以为是碰到大雷，去换了，换的那颗在店里默电P45，垃圾风扇（扣具都没扣），长城300W电源下跑400*8.5。拿回家还是那样。唉，看不少兄弟都用X38DQ6超E0的Q9550啊，难道是我无福消受？？？？救命啊！

alexyin1984

被卖家M2F鸽子，最后上的EP45 Extreme
回家直接480*8.5@1.3V 成功进系统，极限还没测

alexyin1984

我的是1.1版的X48-DQ6，刷F7正式版，我的E5200可以333*12.5，何在P35-DS3L设置上完全一样，唯一不同的就是对内存要求更高了，建议你内存加压试试。
我内存不加压经常会出现BIOS回默，加0.05V就再没出现了，内存效 ...
supertest 发表于 2009-5-8 09:58

你内存够背的

supertest

跟我的情况一样,在秋叶圆买了块X48-DQ6 ,1.3版本,刷了f8d的BIOS
上5电容的E5200,这U在我的ABIT AB9可以上4.2G  
内存是KINGMAX 1066.

试过即使外频调到205,其他默认不变,也无法开机

也试过不同的组合,关节电 ...
kins365 发表于 2009-5-3 08:00

我的是1.1版的X48-DQ6，刷F7正式版，我的E5200可以333*12.5，何在P35-DS3L设置上完全一样，唯一不同的就是对内存要求更高了，建议你内存加压试试。
我内存不加压经常会出现BIOS回默，加0.05V就再没出现了，内存效能设置为中等，3.2B＝1066稳定，3.0A＝1000就不稳定。

susu2933

换吧。。。。。。

alexyin1984

是啊，换完之后至少在换I7以前上内存方便。

haojuegn125

本人用的就是DDR3的775平台

alexyin1984

也是，考虑出了换DDR3的775平台。

alexyin1984

更新F9H BIOS后感觉好点。至少现在可以轻松3.4G了，等BIOS慢慢更新，最新版F9I只是升级了AHCI 的BIOS，唉，烦人，慢慢等。惹急了就连带Q9550，内存出了。

lvhan

主板的可能大  呵呵  我的x38 外频过了450就很不稳定

kins365

跟我的情况一样,在秋叶圆买了块X48-DQ6 ,1.3版本,刷了f8d的BIOS
上5电容的E5200,这U在我的ABIT AB9可以上4.2G  
内存是KINGMAX 1066.

试过即使外频调到205,其他默认不变,也无法开机

也试过不同的组合,关节电,换内存,

根本也点不亮....现在还在郁闷中,

alexyin1984

在tweaktown碰到的那哥们终于给我回信了。超级感动！


Hi there Alex,

No, I haven't tried it in the end - I emailed gigabyte support and got standard answer from them:

"We don't support overclocking, but it may be due to several reasons - bad RAM, bad compatibility, etc... "

I then emailed janus and waited for few weeks, until I was given the exact same bios as you found - F9H. The only problem is that in the meantime I already bought EP45-UD3P, since I couldn't  wait any longer. Guess what - no problems at all - and with exact same setup (same installation of vista, same components - except for motherboard naturally) I could boot with 500+ fsb in vista.
Having settled finally on these settings:



and a little bit higher in the end (with a 1 notch up in vcore and mch core):



Temperatures are awesome (overclock stable with cie and eist enabled) -with core around 35-38c in iddle, and up to 44-45c during normal load (middle 50s when priming - can be seen in picture).

So yes - the problem does indeed lie in x38-dq6 after all (at least in its bios) - and it especially affects 45nm quads - E0 revisions. When raising fsb, something goes berserk and mobo stops recognizing cpu correctly and this then raises number of problems with OS - aka "hardware failures". Seems like F9H was a step in good direction (if you got it stable at 400fsb), and we should get back to gigabyte (especially janus - I can give him his email adress at gigabyte) so that they can help us even further. After all, I thanked janus and told him that will contact him back and pass the bios/info on.
Main thing is that I'm too lazy to be arsed to get x38-dq6 back in buisness and try out this new bios. Mobo is currently lying in a closed box, but if I catch some time off work I will definately try it out.


Kind regards,

Vjeran

jerry7547

多谢楼主提供新BIOS,下了刷新看看.

hazel2

打电话去叫他们再更新下BIOS

cvcvvbvb

典型的bios问题，我用华硕X38的板子连Q9650都识别不了，bios里面温度高达120，刷完最新的bios

就一切正常。默电上3.6，1.275上4G，1.3175V上4.5G

alexyin1984

貌似最近的E0都比较雷
pangauto 发表于 2009-4-21 22:43

非常惊世骇俗的言论。。。不过我这个貌似是BIOS兼容问题。。。

pangauto

貌似最近的E0都比较雷

hghh

7# alexyin1984
谢谢分享,更新了 AHCI ROM

hj7718772

X38应该不至于那么差