POPPUR爱换

 找回密码
 注册

QQ登录

只需一步,快速开始

手机号码,快捷登录

搜索
查看: 10757|回复: 6
打印 上一主题 下一主题

WD 1T 黑盘 WD1002FAEX-00Y9A0 有点小悲剧了.....

[复制链接]
跳转到指定楼层
1#
发表于 2010-8-24 10:11 | 只看该作者 回帖奖励 |倒序浏览 |阅读模式
本帖最后由 Esper 于 2010-8-24 12:09 编辑

据网上其他地方说:

1. MDL后6位是 00Y9A0 的已确认为SATAⅡ3Gb!而不是3代接口6GB/S传输!区分是否为SATA3 6Gb方法!第一 跳线5-6 降低接口速率为1.5Gb的 是SATA2 3Gb盘。跳线5-6 降低接口速率为3.0Gb 的才是SATA3 6Gb盘。 第二 SATA3 6Gb 的5V和12V 功率要高与SATA2 第三最直接的方法就是MDL后6位 00Z3A0才是3代接口,6GB/S传输!而00Y9A0 被证实就是2代接口 3Gb!


2. I bought a WD1002FAEX recently and found during POST that the hard disk's speed was only  3GB/s.  So I took this hard disk to Synnex yesterday and the technician helped me to 're-set' the hard disk speed to 6GB/s.  I was told that the default speed is 3GB/s to prevent accidental damage in case the user's motherboard does not support SATA3.  

So you'd better bring the hard disk back to Synnex for re-setting back to 6GB/s.

3.本人亦有相同遭遇!在高登Centralfield前後兩個月買了兩部WD1002FAEX, 它們的MDL編號最尾都是-00Y9A0, 結果兩部HDD都不能被主機板(Asus P7P55D E-LX)認出是SATA3, 相關的SATA3 Controller(MARVELL 9123)只顯示SATA2. 華碩熱線服服務中心職員對我說是-00Y9A0編號的一批貨出了問題,應立即送去有關代理商更換為MDL編號最尾的4位是Z3A0的. 果然不用半小時的檢查其中一部由SYNNEX代理的便替我更換了一部新的MDL尾碼為-Z3A0的. 他們並未有如Kenn所說的甚麼出廠是設定為Sata2要由服務中心reset為Sata3的說法, 奇怪! 最氣憤的是, 另外一部WD1002FAEX-00Y9A0代理是VST偉仕, 只買了一個多月便出現BAD SECTORS, 而且他們的服務態度極差! 不但沒有即時檢查交去的HDD, 要我確認一張維修表格後便打發我走, 說他們沒有維修部門要等一個星期後才會更換另外一部相同編號-00Y9A0的HDD, 對未能被主機確認為SATA3問題只能等WD廠有Firmware才可解決. 因他們沒有如SYNNEX或XANDER擁有MDL WD...-00Z3A0存貨可以為我更換! 所以各位大哥大姐買VST偉仕的貨品前要認真考慮他們的技術支援及保養問題!


4. 因為我就系上個月系jumb*買左兩只00y9a0(SYNNEX代理),重以為系個底板問題(asus p6x58d-e)搞左好內都系顯示3GB,問asus客服,就話系hdd firmware問題,問WD官方又話無新firmware...後尾發現個個00y9a0  ge都系一樣...

5. Managed to get a reply from Support. It appears that there were several batches of drives that were sold that had firmware improperly configured. This firmware problem seems to be very specific to the lots in question - mine happened to be 00Y9A0 which is one of 5 or 6 so effected.

WD has a batch file that repairs this problem. The provided solution willl not  run in a DOS s** so you you will need to be able to get to a 32-bit command prompt in order to apply. It also appears that the solution provided only looks to find the target HD as Drive C, and in my situation would not find the drive when connected to a SATA III controller. This is also a known "bug" in some cases with certain combinations of motherboards and controllers.

IT was sent to me via email by WD support. I would suggest if you have this issue that you start a support case and they eill confirm that your drive is among those affected.

These are the models the console application works with, per the text file that came with the file I received.:

    WD1002FAEX-00Y9A0
    WD7502AAEX-00Y9A0
    WD6402AAEX-00Y9A0
    WD5002AAEX-00Y9A0
    WD5002AAEX-32Y9A0

Hope that helps.  







我中招了........
2#
 楼主| 发表于 2010-8-24 12:15 | 只看该作者
插在SATA2 3GBPS上 将就用了,

如此WDC啊.....
回复 支持 反对

使用道具 举报

3#
发表于 2010-8-24 17:17 | 只看该作者
八会吧?这不是骗消费者么?
回复 支持 反对

使用道具 举报

4#
发表于 2010-8-24 17:29 | 只看该作者
SATA2和SATA3对机械硬盘而言几乎无意义,就算是ATA 133也够用
回复 支持 反对

使用道具 举报

5#
发表于 2010-8-25 11:03 | 只看该作者
恩,我昨天入了一块,尾号同样是00Y9A0,不过商家答应给我换一块00z3a0,一般情况下,商家不会换的,而且有了通电时间,不过可以发图给他,不由他不换,
图片地址是:http://wdc.custhelp.com/cgi-bin/ ... ds=227%2C279#jumper

这是西数官方网站的资料,清清楚楚的写明了,3Gb接口和6Gb接口的区别,无图无真相,就算西数中国官方不承认,不换都不行
回复 支持 反对

使用道具 举报

6#
发表于 2010-8-25 11:08 | 只看该作者
回复 支持 反对

使用道具 举报

7#
发表于 2010-8-25 11:39 | 只看该作者
SATA3 完全是忽悠
回复 支持 反对

使用道具 举报

您需要登录后才可以回帖 登录 | 注册

本版积分规则

广告投放或合作|网站地图|处罚通告|

GMT+8, 2025-7-29 05:20

Powered by Discuz! X3.4

© 2001-2017 POPPUR.

快速回复 返回顶部 返回列表