RAID 0的问题

zhrrobert

决定过年把DFI NF4U-D换成GA-965P-DS3 ,因为数据太多不好备份,想问一下基于NF4的RAID 0(SEAGATE 7200.9 160G*2)能不能直接用在新板上? 谢谢

falcon_tx

ls上的你用过吗？只要设置正确绝对可以

DayFly

原帖由 falcon_tx 于 2007-2-2 16:16 发表
ls上的你用过吗？只要设置正确绝对可以

你这是误导!

无疑nf3建的raid可到nf4

但是别想到Matrix Raid还能用

farter

Intel® Matrix Storage Manager
Can I move my RAID volume to another system and access the contents?




The hard drive members of a RAID volume can be moved to another system and the contents of that RAID volume can then be accessed. This may be necessary in the event of a motherboard failure.

Requirements
The new system must support Intel® Matrix Storage Technology (i.e. RAID) as well as the RAID volume level of the RAID volume on the hard drives being moved.

As an example, a RAID 5 volume should not be moved to a system with the Intel® 82801ER I/O controller hub (ICH5R) because that I/O controller does not support RAID 5.

Warning
If the new system includes a different I/O controller than the one on which the RAID volume was created, you should not attempt to boot to the RAID volume. You should boot to an operating system on another non-RAID hard drive or RAID volume and from there, access the contents of the original RAID volume.

As an example, if you are moving a RAID 0 volume created on a system with the Intel 82801ER I/O controller hub (ICH5R) to a system with the Intel® 82801GR I/O controller hub (ICH7R), you should not boot to the RAID 0 volume, but should install an operating system on a non-RAID hard drive or a new RAID volume and access the contents of the original RAID 0 volume from within that OS.

If the new system includes the same I/O controller, this warning does not apply.

:lol:

farter

simple.wikipedia.org/wiki/RAID

RAID is not readily moved to a new system. When using a single disk, it is relatively straightforward to move the disk to a new system. Simply connect it to the new system, provided it has the same interface available. However, this is not so easy with a RAID array. A RAID BIOS must be able to read metadata from the array members in order to successfully construct the array and make it accessible to an operating system. Since RAID controller makers use different formats for their metadata (even controllers of different families from the same manufacturer may use incompatible metadata formats) it is virtually impossible to move a RAID array to a different controller. When moving a RAID array to a new system, plans should be made to move the controller as well. With the popularity of motherboard integrated RAID controllers, this is extremely difficult to accomplish. Generally, it is possible to move the RAID array members and controllers as a unit, and software RAID in Linux and Windows Server Products can also work around this limitation, but software RAID has other limitations (mostly performance related).

:lol:

cxlxl

我只搞过从一块975上移植到另一块同品牌同型号975上无问题呵呵

reiayanami

系统盘的数据当然不能移植了，单盘系统盘都不能移植，因为主板不一样了驱动就不能用了，

另外问一下组RAID0的话用个扩展卡是不是更好一点，有没有可以推荐的4口SATA硬盘用的？

InuYasha

NVRAID移到VIA的SATA RAID可以吗?

xiablo

DS3是ICH8不是ICH8R RAID是技嘉的GBB36X

reiayanami

原帖由 zxjike 于 2007-2-2 22:54 发表
我倒是有2个PCI-E的SATA阵列卡，自己用着哈哈。

能不能透露一下你用的卡是什么型号的？多少米啊？效果怎么样？

帝国战猪

原帖由 zxjike 于 2007-2-2 22:54 发表
我倒是有2个PCI-E的SATA阵列卡，自己用着哈哈。

用的啥卡？我的硬盘也没地方接了w00t)

98118

原帖由 帝国战猪 于 2007-2-3 13:29 发表


用的啥卡？我的硬盘也没地方接了w00t)

w00t) w00t) 都是盘多人士呀

InuYasha

谁盘多借我耍耍,我这块主板上8个SATA+2个PATA+两个1394就插了一块硬盘:lol:

[ 本帖最后由 InuYasha 于 2007-2-3 14:59 编辑 ]

帝国战猪

原帖由 98118 于 2007-2-3 14:46 发表

w00t) w00t) 都是盘多人士呀

等小偷来拿硬盘拍死他:loveliness:

zhrrobert

最终的处理方法：买了一个３２０Ｇ的先把数据给拷出来